The MAX6965 I²C-compatible serial interfaced peripheral
provides microprocessors with nine additional output
ports. Each output is an open-drain current-sinking
output rated to 50mA at 7V. All outputs are capable of
driving LEDs, or providing logic outputs with external
resistive pullup up to 7V.
Eight-bit PWM current control is also integrated. Four of
the bits are global control and apply to all LED outputs
to provide coarse adjustment of current from fully off to
fully on with 14 intensity steps. Additionally each output
then has an individual 4-bit control, which further
divides the globally set current into 16 more steps.
Alternatively, the current control can be configured as a
single 8-bit control that sets all outputs at once.
Each output has independent blink timing with two blink
phases. LEDs can be individually set to be either on or off
during either blink phase, or to ignore the blink control.
The blink period is controlled by an external clock (up to
1kHz) on BLINK or by a register. The BLINK input can also
be used as a logic control to turn the LEDs on and off, or
as a general-purpose input (GPI).
The MAX6965 supports hot insertion. The SDA, SCL,
active-low RST, BLINK, and the slave address input AD0 remain
high impedance in power-down (V+ = 0V) with up to 6V
asserted upon them. The output ports remain high
impedance with up to 8V asserted upon them.
The MAX6965 is controlled through a 2-wire I²C serial
interface, and can be configured to one of four I²C
addresses.
* Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product uses. Note that "+", "#", "-" in the part number suffix describes RoHS status. Package drawings may show a different suffix character.
Devices:
1-8 of 8
MAX6965
Free Sample
Buy
Status
Package:
TYPE PINS FOOTPRINT
DRAWING CODE/VAR *
Temp
RoHS/Lead-Free? Materials Analysis
MAX6965AEE
Active
QSOP;16 pin;30.9 mm²
Outline Drawing: 21-0055 (PDF)
Land Pattern: 90-0167 (PDF)
Use pkgcode/variation: E16-4*
MAX6957 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander MAX7301 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port I/O Expander MAX7300 2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or 28-Port I/O Expander MAX6956 2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or 28-Port LED Display Driver and I/O Expander MAX7310 2-Wire-Interfaced 8-Bit I/O Port Expander with Reset MAX7311 2-Wire-Interfaced 16-Bit I/O Port Expander with Interrupt and Hot-Insertion Protection MAX6965 9-Output LED Driver with Intensity Control and Hot-Insertion Protection MAX7312 2-Wire-Interfaced 16-Bit I/O Port Expander with Interrupt and Hot-Insertion Protection MAX7313 16-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection MAX7315 8-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection MAX7316 10-Port I/O Expander with LED Intensity Control, Interrupt, and Hot-Insertion Protection MAX7314 18-Port GPIO with LED Intensity Control, Interrupt, and Hot-Insertion Protection MAX6964 17-Output LED Driver/GPO with Intensity Control and Hot-Insertion Protection MAX7317 10-Port SPI-Interfaced I/O Expander with Overvoltage and Hot-Insertion Protection MAX7318 2-Wire-Interfaced, 16-Bit, I/O Port Expander with Interrupt and Hot-Insertion Protection
Download
E-Mail