QuickView - DS80C400 Network Microcontroller

Description

FULL DATA SHEET (PDF, 1.8MB)
Download	E-Mail

The DS80C400 network microcontroller offers the highest integration available in an 8051 device. Peripherals include a 10/100 Ethernet MAC, three serial ports, a CAN 2.0B controller, 1-Wire® Master, and 64 I/O pins.

To enable access to the network, a full application-accessible TCP IPv4/6 network stack and OS are provided in ROM. The network stack supports up to 32 simultaneous TCP connections and can transfer up to 5Mbps through the Ethernet MAC. Its maximum system-clock frequency of 75MHz results in a minimum instruction cycle time of 54ns. Access to large program or data memory areas is simplified with a 24-bit addressing scheme that supports up to 16MB of contiguous memory.

To accelerate data transfers between the microcontroller and memory, the DS80C400 provides four data pointers, each of which can be configured to automatically increment or decrement upon execution of certain data pointer-related instructions. The DS80C400's hardware math accelerator further increases the speed of 32-bit and 16-bit multiply and divide operations as well as high-speed shift, normalization, and accumulate functions.

The High-Speed Microcontroller User's Guide and the High-Speed Microcontroller User's Guide: Network Microcontroller Supplement should be used in conjunction with this data sheet. Download both at www.maxim-ic.com/microcontrollers.

Comparison Table

Part Number
and
Description

Internal Program Memory

Internal MOVX SRAM

Serial Ports

16-bit Timers

Data Pointers

10/100 Ethernet MAC

1-Wire Master

Watchdog

Power Fail Reset & Interrupt

Power Mgmt. Mode

Supply Voltage (V)

Package

DS80C400
Network Microcontroller

64kB ROM

1kB

Yes

1.8
3.3

100/LQFP

DS80C410
Network Microcontrollers with Ethernet and CAN

64kB ROM

73.5kB

Yes

1.8
3.3

100/LQFP

DS80C411
Network Microcontrollers with Ethernet MAC

64kB ROM

73.5kB

Yes

1.8
3.3

100/LQFP

An evaluation kit is available: DSTINIm400 DSTINIs-005, DSTINIs-006, DSTINIs400 DS80C400-KIT

Key Features

Applications/Uses

High-Performance Architecture
- Single 8051 Instruction Cycle in 54ns
- DC to 75MHz Clock Rate
- Flat 16MB Address Space
- Four Data Pointers with Auto-Increment/Decrement and Select-Accelerate Data Movement
- 16/32-Bit Math Accelerator
Multitiered Networking and I/O
- 10/100 Ethernet Media Access Controller (MAC)
- CAN 2.0B Controller
- 1-Wire Net Controller
- Three Full-Duplex Hardware Serial Ports
- Up to Eight Bidirectional 8-Bit Ports (64 Digital I/O Pins)
Robust ROM Firmware
- Supports Network Boot Over Ethernet Using DHCP and TFTP
- Full, Application-Accessible TCP/IP Network Stack
- Supports IPv4 and IPv6
- Implements UDP, TCP, DHCP, ICMP, and IGMP
- Preemptive, Priority-Based Task Scheduler
- MAC Address Can Optionally Be Acquired from IEEE-Registered DS2502-E48
10/100 Ethernet Mac
- Flexible IEEE 802.3 MII (10/100Mbps) and ENDEC (10Mbps) Interfaces Allow Selection of PHY
- Low-Power Operation: Ultra-Low-Power Sleep Mode with Magic Packet® and Wake-Up Frame Detection
- 8kB On-Chip Tx/Rx Packet Data Memory with Buffer Control Unit Reduces Load on CPU
- Half- or Full-Duplex Operation with Flow Control
- Multicast/Broadcast Address Filtering with VLAN Support
Full-Function CAN 2.0B Controller
- 15 Message Centers
- Supports Standard (11-Bit) and Extended (29-Bit) Identifiers and Global Masks
- Media Byte Filtering to Support DeviceNet™, SDS, and Higher Layer CAN Protocols
- Auto-Baud Mode and SIESTA Low-Power Mode
Integrated Primary System Logic
- 16 Total Interrupt Sources with Six External
- Four 16-Bit Timer/Counters
- 2x/4x Clock Multiplier Reduces Electromagnetic Interference (EMI)
- Programmable Watchdog Timer
- Oscillator-Fail Detection
- Programmable IrDA Clock

Features continued on page 32 of the full data sheet.

	Analog Modems
	Automatic Meter Reading/900MHz-ISM
	Automatic Teller Machine Systems
	Data Converters (Serial-to-Ethernet, CAN-to-Ethernet)
	Environmental Monitoring
	Home/Office Automation
	Industrial Control and Automation
	Network Sensors
	Portable Point-of-Sales Equipment
	Remote Data-Collection Equipment
	Security Systems
	Transaction/Payment Terminals
	Vending

Key Specifications: Networked Microcontrollers

Part Number

Internal Program Memory

Internal MOVX SRAM

Serial Ports

16-Bit Timers

Data Pointers

10/100 Ethernet MAC

1-Wire

CAN 2.0B Controller

Watchdog

Pwr. Fail Reset and Interr.

Pwr. Mgmt. Mode

Ring Osc.

Features

EV Kit

Package/Pins

Price

See Notes

DS80C400

64kB ROM

1kB

Yes

Master

Yes

16/32-bit Math Coprocessor

256-Byte Internal Scratchpad

Data Pointer Decrement

Low Cost, High Speed

Multiple External Interrupts

Six External Interrupts

LQFP/100

$8.89 @1k

See All Networked Microcontrollers (9)