ENGLISH • 简体中文 • 日本語 • 한국어  

    Login | Register 


   
 
Enter keywords or part number    


What's New Products Solutions Design AppNotes Support Sales About Us Members

Maxim > Products > [Optoelectronics] 
MAX3510
Upstream CATV Amplifier


  QuickView     Technical Documents     Ordering Info     More Information     User Comments (0)     All  
Status
All versions are No Longer Available.

Data Sheet
FULL DATA SHEET (PDF, 156kB)
Download this datasheet in PDF formatDownload   Send this datasheet to any email addressE-Mail

Description
The MAX3510 is a programmable power amplifier for use in CATV upstream applications. The device outputs up to 64dBmV (continuous wave) through a 2:1 (voltage ratio) transformer. It features variable gain controlled by a 3-wire digital serial bus. Gain control is available in 1dB steps. The device operates over a frequency range of 5MHz to 65MHz.

The MAX3510 offers a transmit-disable mode, which places the device in a high-isolation state for use between bursts in TDMA systems. In this mode the output stage is shut off, minimizing output noise. When entering and leaving transmit-disable mode, transients are kept to 7mV nominal at full gain. In addition, supply current is reduced to 25mA.

Two power-down modes are available. Software-shutdown mode permits power-down of all analog circuitry while maintaining the programmed gain setting. Shutdown mode disables all circuitry and reduces current consumption to less than 10µA.

The MAX3510 is available in a 20-pin QSOP package for the extended-industrial temperature range (-40°C to +85°C).

An evaluation kit is available:  MAX3510EVKIT  

NOTE: This product requires use of the following:

  • MAX3510 PC-Control Software

    Key Features   Applications/Uses
    • Ultra-Low Power-Up/Down Transients, 7mV Typical at 59dBmV Output
    • Single +5V Supply
    • Output Level Ranges from <8dBmV to 64dBmV
    • Gain Programmable in 1dB Steps
    • Low Transmit Output Noise Floor: -47dBmV (160kHz BW)
    • Low Transmit-Disable Output Noise: -70dBmV
    • Two Power-Down Modes

    		 
  		• Cable Modems
  		• Cable Television Set-Top Boxes
  		• CATV Status Monitors
  		• Telephony-Over-Cable

    Diagram
    MAX3510: Typical Operating Circuit
    Typical Operating Circuit

    Application Notes
  		• Application Note 587: Block Diagram for MAX3510 Upstream CATV Amplifier Application - MAX3510
  		• Application Note 780: CATV Upstream Amplifier Selection Guide - MAX3510
  		• Application Note 799: REP029: MAX3510 Cable Upstream Amplifier Harmonic Distortion Performance to 55MHz - MAX3510
  		• Application Note 808: CATV dBm, dBmV, and dBµV Conversions - MAX3510
  		• Application Note 972: CATV Minimum Loss Pad for 75Ω Measurements - MAX3510
  		• Application Note 1745: The MAX3510/MAX3514/MAX3516 Cable Upstream Amplifiers ACPR (Adjacent Channel Power Ratio) Performance - MAX3510
  		• Application Note 1945: Performance of Maxim's Cable Upstream Amplifier Meets DOCSIS 2.0 Requirements - MAX3510
  		• Application Note 2866: Converting S-Parameters from 50Ω to 75Ω Impedance - MAX3510

    Evaluation Kits
  		• MAX3510EVKIT

    Design Guides
  		• Fiber (PDF)

    Reliability Reports
  		• Show FIT data for:
  		• Request Reliability Report for:

    Software/Models
  		• MAX3510 PC-Control Software

    Ordering Information
    Notes:

    1. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
    2. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day.
    3. Part number suffixes: T or T&R = tape and reel;+ = RoHS/lead-free;# = RoHS/lead-exempt. More: SeeFull Data Sheet or Part Naming Conventions.
    4. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product uses. Note that "+", "#", "-" in the part number suffix describes RoHS status. Package drawings may show a different suffix character.


    Devices: 1-4 of 4

    MAX3510 Free
    Sample    		 Buy Status
    Package: TYPE PINS FOOTPRINT
      DRAWING CODE/VAR *
    		Temp RoHS/Lead-Free?
    Materials Analysis
    MAX3510EEP     N/A No Longer Available QSOP;20 pin;54 mm²
    Outline Drawing: 21-0055 (PDF)
    Land Pattern: 90-0168 (PDF)
    Use pkgcode/variation: E20-1*
    		-40°C to +85°C RoHS/Lead-Free: No
    Materials Analysis
    MAX3510EEP-T     N/A No Longer Available QSOP;20 pin;54 mm²
    Outline Drawing: 21-0055 (PDF)
    Land Pattern: 90-0168 (PDF)
    Use pkgcode/variation: E20-1*
    		-40°C to +85°C RoHS/Lead-Free: No
    Materials Analysis
    MAX3510EEP+     N/A No Longer Available QSOP;20 pin;54 mm²
    Outline Drawing: 21-0055 (PDF)
    Land Pattern: 90-0168 (PDF)
    Use pkgcode/variation: E20+1*
    		-40°C to +85°C RoHS/Lead-Free: Lead Free
    Materials Analysis
    MAX3510EEP+T     N/A No Longer Available QSOP;20 pin;54 mm²
    Outline Drawing: 21-0055 (PDF)
    Land Pattern: 90-0168 (PDF)
    Use pkgcode/variation: E20+1*
    		-40°C to +85°C RoHS/Lead-Free: Lead Free
    Materials Analysis

    Didn't Find What You Need?
  • Next Day Product Selection Assistance from Applications Engineers
  • Parametric Search
  • Applications Help

    •  QuickView   Technical Documents   Ordering Info   More Information  
     Description 
     Key Features 
     Applications/Uses 
     Key Specifications 
     Diagram 

    		 Data Sheet 
     Application Notes 
     Design Guides 
     Engineering Journals 
     Reliability Reports 
     Software/Models 
     Evaluation Kits 

    		 Price and Availability 
     Samples 
     Buy Online 
     Package Information 
     Lead-Free Information 

    		 Related Products 
     Notes and Comments 
     Evaluation Kits 

    Document Ref.: 19-1398; Rev 4; 2007-06-13
    This page last modified: 2007-06-13


    •         •         •         •     Privacy Policy     •     Legal Notices

        Copyright © 2009 by Maxim Integrated Products