Search Results: Impedance

General Network Interface Design Criteria for the DS2153 and ... [Open results in new window]
... Matching source impedance to the characteristic impedance of the line prevents ... L1,
L0, Application, Transformer N, Return Loss¹, Z Rt ². 0, 0, 0, 75 ohm normal, ...
japan.maxim-ic.com/appnotes.cfm/an_pk/352 - 25k

Analysis of ADC System Distortion Caused by Source Resistance ... [Open results in new window]
... キーワード: ADC, analog to digital converter, voltage divider, distortion, gain
error, high impedance, low impedance, sampling capacitor, time constant, a ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1948 - 35k

Characterizing the S-Parameters of 75Ω Circuits using 50Ω Lab ... [Open results in new window]
... mlp, min loss pad, minimum loss pad, 75, 75ohm, 75 ohm. ... of the instrument to the
native 75Ω impedance of the ... The math required to transform Z LOAD into Z LOAD ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3250 - 28k

Exact Circuit Analysis with Microsoft Excel - マキシム [Open results in new window]
... with entries for the R, the C, and a frequency sweep as shown in Figure 2. Figure
2. Excel spreadsheet calculates RC impedance. The equation for Z in is ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1947 - 24k

Low-Noise Amplifier Stability Concept to Practical Considerations ... [Open results in new window]
... Voltage, current, or power emanating from a source impedance Z s and delivered to
a load Z L can be regarded as the sum of incident and reflected waves ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1849 - 37k

General Network Interface Design Criteria for the DS2151 and ... [Open results in new window]
... volts, therefore the impedance that the transmitter sees must now be 65Ω and the
net impedance seen by ... The same 3 volt pulse over a 100 ohm load is required. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/353 - 23k

Low-Noise Amplifier Stability Concept to Practical Considerations ... [Open results in new window]
... is plotted in red on the Smith Chart (Figure 2). As read from the chart, it represents
a desired load impedance of Z L = 50(01.47 -J0.13)Ω = 73.5 – J6.5Ω. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1852 - 38k

Improving Gain Flatness without Sacrificing Dynamic Performance in ... [Open results in new window]
... In this configuration, a single-ended signal from a 50Ω impedance source is
converted to a differential signal through the transformer. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3228 - 28k

Variations Among Current-Sink/Source Circuits with a Single Op Amp ... [Open results in new window]
... Performance data are discussed, and illustrate the different compromises between
precision, dynamic impedance, and compliance range for some of the circuit ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3869 - 23k

Amplifier Provides Signal Conditioning for Piezofilm Sensor ... [Open results in new window]
... キーワード: thermal sensor, temperature sensor, piezoelectric, high-impedance input,
high-Z buffer amplifier, temp sensor, piezo, charge amplifier, high ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1127 - 25k

Using the MAX4090 with the Reconstruction Filter - マキシム [Open results in new window]
... A low input impedance (< 100Ω) is required by the MAX4090 in normal operation, special
care must be taken when a reconstruction filter is used in front of the ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3305 - 24k

Tech Tips: Getting the Most from Your Sensor and Conditioning ... [Open results in new window]
... Buffer the power input with a low-impedance resistor and capacitor as close to the ...
A 10-ohm resistor and a 0.1_F capacitor will greatly reduce the effects of ...
japan.maxim-ic.com/appnotes.cfm/an_pk/637 - 32k

Driving Audio Piezoelectric Transducers - マキシム [Open results in new window]
... What is the effect of source impedance versus sound pressure when driving
an audible PZT? ... What does the impedance of a PZT look like? ...
japan.maxim-ic.com/appnotes.cfm/an_pk/988 - 45k

Pulse Template Measurement - マキシム [Open results in new window]
... The DSMAT75X12 is a 12x1 matrix with 75ohm impedance matching and is designed for ...
T1 and E1 modes with a variety of termination configurations: 75/100/120 ohm. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/397 - 36k

Noise Reduction For ADSL Modem Power - マキシム [Open results in new window]
... The key is to realize that this voltage will be induced and create a high impedance
path where this noise voltage can harmlessly be absorbed. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1843 - 23k

EPOT Applications: Offset Adjustment in Op-Amp Circuits ... [Open results in new window]
... The EPOT offset network can be viewed as a voltage source with a source impedance
of R2. ... However, in most configurations, the impedance of Rth is negligible. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/803 - 27k

Designing Large Video-Crosspoint Systems Just Got Easier ... [Open results in new window]
... Each input and output is buffered and all outputs can be individually set for high
impedance disbale or gain = 1V/V or 2V/V. Analog video switching constitutes ...
japan.maxim-ic.com/appnotes.cfm/an_pk/795 - 37k

5V Auxiliary Power Supply Teams LDO and Charge Pump - マキシム [Open results in new window]
... to 5V. To counteract the effect of high source impedance in the charge
pump, provide feedback from the output to the LDO. The 5V ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3202 - 24k

Using Analog Temperature Sensors with ADCs - マキシム [Open results in new window]
... concepts. Source Impedance. Most ... Most general-purpose ADCs have maximum source-impedance
limits somewhere between 1kΩ and 10kΩ. Analog temperature ...
japan.maxim-ic.com/appnotes.cfm/an_pk/571 - 24k