Search Results: Contact Bounce

Circuit Removes Relay-Contact Bounce - マキシム [Open results in new window]
... controller. An example of relay-contact bounce (Figure 2) shows three bounces
with an inrush current peak of almost 30A. (The top ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3743 - 21k

Protecting Against Momentary Power Loss Due to Battery-Bounce ... [Open results in new window]
... Against Momentary Power Loss Due to Battery-Bounce. ... can cause momentary interruptions
when batteries lose contact. ... the impact can open internal contacts for as ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3209 - 23k

Interfacing Switches and Relays to the Real World in Real Time ... [Open results in new window]
... キーワード: switch debouncers, 15kV, ESD, switch protection ... Contact bounce is not
acceptable, because automotive ... application note, "Switch Bounce and Other ...
japan.maxim-ic.com/appnotes.cfm/an_pk/764/ - 52k

Semiconductor Toggle Switch - マキシム [Open results in new window]
... Power is delivered by circuitry rather than a pair of contacts that go straight
to the battery. Protection can be provided against contact bounce and power ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3223 - 23k

[PDF] アプリケーションノート [Open results in new window]
... Initial Contact Contact Bounce Good Contact Poor contact >10ms Average of
100 contacts using a shorted iButton Page 7. AN159 7 of 21 ...
pdfserv.maxim-ic.com/jp/an/AN159J.pdf

-48V Hot Swap Solution For Telecom Line Cards Assures Immunity To ... [Open results in new window]
... the controller holds power switch Q1 in the OFF state for 300ms, allowing time for
the card to be firmly in place and connector-contact bounce to settle before ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1881 - 35k

Switching Between Battery and External Power Sources ... [Open results in new window]
... First, contact bounce effects can occur when the external source is connected and
disconnected, resulting in power spikes, as shown in Figure 2. Second, the ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1136 - 24k

Manually Operated Digital Potentiometer Doesn't Need a ... [Open results in new window]
... microcontroller. To mask the effect of contact bounce in mechanical switches
S1 and S2, a dual switch debouncer (IC1) is used. A ...
japan.maxim-ic.com/appnotes.cfm/an_pk/1118 - 22k

Where Is Ground? - マキシム [Open results in new window]
... In simple terms, as the switch starts opening on the +25V side, the contact
will bounce between open circuit and being connected to +25V. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/4292/ - 33k

Interfacing SD Cards with the TINI System - マキシム [Open results in new window]
... Error detection allows for robust error recovery in the event of physically induced
errors such as contact bounce during insertion and removal or nonideal ...
japan.maxim-ic.com/appnotes.cfm/an_pk/4068 - 36k

Pushbuttons Control Regulated Switching Converter - マキシム [Open results in new window]
... A time-delay network (R1, R2, and C1) masks the switch bounce on S1 that would ... pin
to ramp slowly to 0V, thereby removing the effect of any bounce that occurs ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3535 - 22k

Single-Pushbutton ON/OFF Power Control - マキシム [Open results in new window]
... キーワード: pushbutton power switches, switch debouncers, LDO linear regulator,
flip-flops. ... The normally open (NO) single-contact pushbutton connects to a ...
japan.maxim-ic.com/appnotes.cfm/an_pk/4444 - 21k

Using a Keypad and LCD Display with the MAXQ2000 - マキシム [Open results in new window]
... Additionally, to prevent the bouncing contacts of a switch from registering multiple
presses, the application requires that a key be held down for a certain ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3414 - 36k

SHA iButton Secrets and Challenges - マキシム [Open results in new window]
... the speed of a bar code target, time for an LCD display to issue READY status after
a character write, bounce of a mechanical switch or relay contact, etc.); ...
japan.maxim-ic.com/appnotes.cfm/an_pk/152 - 36k

Design Considerations for Data-Lump Cables - マキシム [Open results in new window]
... 8kV, IEC 1000-4-2, Contact Discharge Method. ... the fault current goes to ground, the
ground connection should be kept short to reduce the effects of ground bounce. ...
japan.maxim-ic.com/appnotes.cfm/an_pk/739 - 42k

The MAXQ Microcontroller in Action: Designing a Bicycle Computer ... [Open results in new window]
... measurements: a magnet passes over a reed switch and closes a contact, causing the ...
too close to the sensor, making the whole DS2423 circuit bounce around a lot ...
japan.maxim-ic.com/appnotes.cfm/an_pk/3845 - 44k