MAX17085B Integrated Charger, Dual Main Step-Down Controllers, and Dual LDO Regulators All-in-One IC Solution Combines Battery Charger and System Power

Overview

Technical Documents

Ordering Info

Related Products

User Comments (0)

All

Status Active: In Production. Description The MAX17085B is an all-in-one notebook power solution integrating a multichemistry battery charger, dual fixed output Quick-PWM™ step-down controllers, and dual keep-alive linear regulators: Charger: The high-frequency (~1.4MHz) multichemistry battery charger uses a current-mode, fixed inductor current ripple architecture that significantly reduces component size and cost. Low-offset sense amplifiers allow the use of low-value sense resistors for charging and input current limit. The charger uses n-channel switching MOSFETs. Adjustable charge current, charge voltage, and cell selection allow for flexible use with different battery packs. Charge current is set by an analog control input, or a PWM input. High-accuracy current-sense amplifiers provide fast cycle-by-cycle current-mode control to protect against short circuits to the battery and respond quickly to system load transients. Additionally, the charger provides a high-accuracy analog output that is proportional to the adapter current. An integrated charge pump controls an n-channel adapter selector switch. The charge pump remains active even when the charger is off. When the adapter is absent, a p-channel MOSFET selects the battery. Main SMPS: The dual Quick-PWM step-down controllers with synchronous rectification generate the 5V and 3.3V main power in a notebook. Low-side MOSFET sensing provides a simple low-cost, highly efficient valley current-limit protection. The MAX17085B also includes output undervoltage, output overvoltage, and thermal-fault protection. Separate enable inputs for each SMPS and a combined open-drain power-good output allow flexible power sequencing. Voltage soft-start reduces inrush current, while passive shutdown discharges the output through an internal switch. Fast transient response, with an extended on-time feature reduces output capacitance requirements. Selectable pulse-skipping mode and ultrasonic mode improve light-load efficiency. Ultrasonic mode operation maintains a minimum switching frequency at light loads, minimizing audible noise effects. Dual LDO Regulators: An internal 5V/100mA LDO5 with switchover can be used to either generate the 5V bias needed for power-up or other lower power "always-on" suspend supplies. Another 3.3V/50mA LDO3 provides "always-on" power to a system microcontroller.

Data Sheet Download Rev 1 (PDF, 3.4MB) E-Mail

An evaluation kit is available: MAX17085BEVKIT

Key Features All-in-One Charger Plus Dual Main Step-Down Controllers 5V/100mA and 3.3V/50mA LDO Regulators Main Dual Quick-PWM with Fast Transient Response and Extended On-Time 300kHz to 800kHz Switching Frequency Fixed 5V and 3.3V SMPS Outputs Low-Noise Ultrasonic Mode Autoretry Fault Protection Charger High Switching Frequency (1.4MHz) Selectable 2-, 3-, and 4-Cell Battery Voltage Automatic Selection of System Power Source Internal Charge-Pump for Adapter n-channel MOSFETs Drive ±0.4% Accurate Charge Voltage ±2.5% Accurate Input Current Limiting ±3% Accurate Charge Current Monitor Outputs for AC Adapter Current (±2% Accuracy) Battery Discharge Current (±2% Accuracy) AC Adapter OK Analog/PWM (100Hz to 500kHz) Adjustable Charge Current Setting AC Adapter Overvoltage and Overcurrent Protection   Applications/Uses 2-to-4, Li+-Cell, Battery-Powered Devices 5V and 3.3V Supplies Notebook Computers PDAs and Mobile Communicators

Diagram

More Information

New Product Press Release

[ 2010-04-27 ]

Didn't Find What You Need?

Information Index

Document Ref.: 19-5135 Rev 1; 2010-10-21
This page last modified: 2010-10-21