|
DS1875
PON Triplexer and SFP Controller
Industry's Next-Generation PON/SFP Controller with APD Boost Converter for Fiber Optic Modules
|
Status
Active: In Production.
Description
The DS1875 controls and monitors all functions for burst-mode transmitters, APD receivers, and video receivers. It also includes a power-supply controller for APD bias generation, and provides all SFF-8472 diagnostic and monitoring functionality. The combined solution of the DS1875 and the MAX3643 laser driver provides APC loop, modulation current control, and eye safety functionality. Ten ADC channels monitor VCC, temperature (both internal signals), and eight external monitor inputs (MON1–MON8) that can be used to meet transmitter, digital receiver, video receiver, and APD receiver-signal monitoring requirements. Four total DAC outputs are available. A PWM controller with feedback and compensation pins can be used to generate the bias for an APD or as a step-down converter. Five I/O pins allow additional monitoring and configuration.
|
|
Data Sheet
|
Key Features
- Meets All PON Burst-Timing Requirements for Burst-Mode Operation
- Laser Bias Controlled by APC Loop and Temperature Lookup Table (LUT)
- Laser Modulation Controlled by Temperature LUT
- Six Total DACs: Four External, Two Internal
- Two 8-Bit DACs, One of Which is Optionally Controlled by MON4 Voltage
- Internal 8-Bit DAC Controlled by a Temperature-Indexed LUT
- PWM Controller
- Boost or Buck Mode
- Boost Mode: Uses Optional External Components, Up to 90V Bias Generation
- 131kHz, 262kHz, 525kHz, or 1050kHz Selectable-Switching Frequency
- APD Overcurrent Protection Using Optional Fast Shutdown
- 10 Analog Monitor Channels: Temperature, VCC, Eight Monitors
- Internal, Factory-Calibrated Temperature Sensor
- RSSI with 29dB Electrical Dynamic
- Five I/O Pins for Additional Control and Monitoring Functions, Four of Which are Either Digital I/O or Analog Monitors
- Comprehensive Fault-Measurement System with Maskable Laser Shutdown Capability
- Two-Level Password Access to Protect Calibration Data
- 120 Bytes of Password-1 Protected Memory
- 128 Bytes of Password-2 Protected Memory in Main Device Address
- 256 Additional Bytes Located at A0h Slave Address
- I²C-Compatible Interface for Calibration and Monitoring
- 2.85V to 3.9V Operating Voltage Range
- -40°C to +95°C Operating Temperature Range
- 38-Pin TQFN (5mm x 7mm) Package
|
|
Applications/Uses
- APD Controller
- BPON, GPON, or EPON Optical Triplexers
- SFF, SFP, and SFP+ Transceiver Modules
|
|
|
|
Key Specifications:
| Fiber Monitoring and Control |
| Part Number |
ADCs |
Resolution
(bits) |
DACs/ Resistors |
FS Out
(kΩ) |
Steps |
Temp. Sensor |
Memory |
VSUPPLY
(V) |
Control Interface |
EV Kit |
Budgetary Price |
| See Notes |
| DS1875 |
10-Input Muxable |
13 |
4 DACs |
None |
256 or 4096 |
Internal |
EEPROM |
2.85 to 3.9 |
I2C |
Yes |
$3.11 @1k |
|
See All Fiber Monitoring and Control (19)
|
Pricing Notes:
This pricing is BUDGETARY, for comparing similar parts. Prices are in U.S. dollars and subject to change. Quantity pricing may vary substantially and international prices may differ due to local duties, taxes, fees, and exchange rates. For volume-specific prices and delivery, please see the price and availability page or contact an authorized distributor.
|
|
Diagram
Typical Operating Circuit
Application Notes
Product Guides
Reliability Reports
Software/Models
Ordering Information
|
Part Number
|
Free
Sample |
Buy |
Status
|
Package:
TYPE PINS FOOTPRINT
DRAWING CODE/VAR *
|
Temp |
RoHS/Lead-Free?
Materials Analysis
|
| DS1875T+
|
|
|
Active |
TQFN;38 pin;36.2 mm²
Outline Drawing:21-0172 (PDF)
Land Pattern: 90-0076 (PDF)
Use pkgcode/variation: T3857+1*
|
-40°C to +85°C
|
RoHS/Lead-Free: Lead Free
Materials Analysis |
| DS1875T+T&R
|
|
|
Active |
TQFN;38 pin;36.2 mm²
Outline Drawing:21-0172 (PDF)
Land Pattern: 90-0076 (PDF)
Use pkgcode/variation: T3857+1*
|
-40°C to +85°C
|
RoHS/Lead-Free: Lead Free
Materials Analysis |
Notes:
- Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
- Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day.
- Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt; -D = drypack; -U/+U on DS parts = cut tape. More: See Full Data Sheet or Maxim Product Naming Conventions.
- * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product uses. Note that "+", "#", "-" in the part number suffix describes RoHS status. Package drawings may show a different suffix character.
|
Similar Products by Function
Similar Products by Application
More Information
Didn't Find What You Need?
Information Index
Rev 1;
2008-10-30
This page last modified: 2010-01-26
|
Download
E-Mail