|
MAX19711
10-Bit, 11Msps, Full-Duplex, Analog Front-End
Ultra-Low-Power, Highly Integrated Transmit and Receive AFE with CDMA Filters
|
Status
All versions are No Longer Available. See Ordering Information for recommended replacements.
Description
The MAX19711 is an ultra-low-power, highly integrated mixed-signal analog front-end (AFE) ideal for CDMA communication applications operating in full-duplex (FD) mode. Optimized for high dynamic performance and ultra-low power, the device integrates a dual 10-bit, 11Msps receive (Rx) ADC; dual 10-bit, 11Msps transmit (Tx) DAC with CDMA baseband filters; three fast-settling 12-bit aux-DAC channels for ancillary RF front-end control; and a 10-bit, 333ksps housekeeping aux-ADC. The typical operating power in FD mode is 37.5mW/42.7mW at a 4.915MHz/11MHz clock frequency.
The Rx ADCs feature 54.8dB SNR and 74.2dBc SFDR at 1.875MHz input frequency with an 11MHz clock frequency. The analog I/Q input amplifiers are fully differential and accept 1.024VP-P full-scale signals. Typical I/Q channel matching is ±0.01° phase and ±0.01dB gain.
The Tx DACs with CDMA lowpass filters feature -3dB cutoff frequency of 1.3MHz and > 64dBc stopband rejection at fIMAGE = 4.285MHz at fCLK = 4.915MHz. The analog I-Q full-scale output voltage range is selectable at ±410mV or ±500mV differential. The output DC common-mode voltage is selectable from 0.86V to 1.36V. The I/Q channel offset is adjustable to optimize radio lineup sideband/carrier suppression. Typical I-Q channel matching is ±0.03dB gain and ±0.07° phase.
Two independent 10-bit parallel, high-speed digital buses used by the Rx ADC and Tx DAC allow full-duplex operation for frequency-division duplex applications. The Rx ADC and Tx DAC can be disabled independently to optimize power management. A 3-wire serial interface controls power-management modes, the
aux-DAC channels, and the aux-ADC channels.
The MAX19711 operates on a single 2.7V to 3.3V analog supply and 1.8V to 3.3V digital I/O supply. The MAX19711 is specified for the extended (-40°C to +85°C) temperature range and is available in a 56-pin, thin QFN package. The Selector Guide at the end of the data sheet lists other pin-compatible versions in this AFE family. For time-division duplex (TDD) applications, refer to the MAX19705–MAX19708 AFE family of products.
|
|
Data Sheet
|
An evaluation kit is available: MAX19710EVCMODU, MAX19710EVKIT, MAX19711EVCMODU, MAX19711EVKIT, MAX19712EVCMODU, MAX19712EVKIT, MAX19713EVCMODU, MAX19713EVKIT
Key Features
- Dual 10-Bit, 11Msps Rx ADC and Dual 10-Bit, 11Msps Tx DAC
- Ultra-Low Power
- 37.5mW/42.7mW at fCLK = 4.915MHz/11MHz, FD Mode
- 24.3mW at fCLK = 11MHz, Slow Rx Mode
- 34.5mW at fCLK = 11MHz, Slow Tx Mode
- Low-Current Standby and Shutdown Modes
- Integrated CDMA Filters with > 64dBc Stopband Rejection
- Programmable Tx DAC Common-Mode DC Level and I/Q Offset Trim
- Excellent Dynamic Performance
- SNR = 54.8dB at fIN = 1.875MHz (Rx ADC)
- SFDR = 75dBc at fOUT = 620kHz (Tx DAC)
- Three 12-Bit, 1µs Aux-DACs
- 10-Bit, 333ksps Aux-ADC with 4:1 Input Mux and Data Averaging
- Excellent Gain/Phase Match
- ±0.01° Phase, ±0.01dB Gain (Rx ADC) at fIN = 1.87MHz
- Multiplexed Parallel Digital I/O
- Serial-Interface Control
- Versatile Power-Control Circuits
- Shutdown, Standby, Idle, Tx/Rx Disable
- Miniature 56-Pin Thin QFN
|
|
Applications/Uses
- CDMA Data Cards
- CDMA Handsets
- Portable Communication Equipment
|
|
|
|
Diagram
 Typical Operating Circuit
Reliability Reports
| Show FIT data for: |
|
| Request Reliability Report for: |
|
Software/Models
Ordering Information
|
Part Number
|
Free
Sample |
Buy |
Status
|
Recommended Replacement |
Package:
TYPE PINS FOOTPRINT
DRAWING CODE/VAR *
|
Temp |
RoHS/Lead-Free?
Materials Analysis
|
| MAX19711ETN
|
|
N/A |
No Longer Available |
MAX19713ETN+
|
TQFN;56 pin;49.1 mm²
Outline Drawing:21-0144 (PDF)
Land Pattern: 90-0043 (PDF)
Use pkgcode/variation: T5677-2*
|
-40°C to +85°C
|
RoHS/Lead-Free: No
Materials Analysis |
| MAX19711ETN+
|
|
N/A |
No Longer Available |
MAX19713ETN+
|
TQFN;56 pin;49.1 mm²
Outline Drawing:21-0144 (PDF)
Land Pattern: 90-0043 (PDF)
Use pkgcode/variation: T5677+2*
|
-40°C to +85°C
|
RoHS/Lead-Free: Lead Free
Materials Analysis |
| MAX19711ETN+T
|
|
N/A |
No Longer Available |
MAX19713ETN+
|
QFN;56 pin
Land Pattern: Not Available
|
-40°C to +85°C
|
See data sheet
|
| MAX19711ETN-T
|
|
N/A |
No Longer Available |
MAX19713ETN+
|
QFN;56 pin
Land Pattern: Not Available
|
-40°C to +85°C
|
See data sheet
|
Notes:
- Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
- Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day.
- Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt; -D = drypack; -U/+U on DS parts = cut tape. More: See Full Data Sheet or Maxim Product Naming Conventions.
- * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product uses. Note that "+", "#", "-" in the part number suffix describes RoHS status. Package drawings may show a different suffix character.
|
Similar Products by Function
| MAX19708 |
10-bit, 11Msps, Ultra-Low-Power Analog Front-End |
| MAX19705 |
10-bit, 7.5Msps, Ultra-Low-Power Analog Front-End |
| MAX19707 |
10-Bit, 45Msps, Ultra-Low-Power Analog Front-End |
| MAX19706 |
10-Bit, 22Msps, Ultra-Low-Power Analog Front-End |
| MAX19712 |
10-Bit, 22Msps, Full-Duplex, Analog Front-End |
| MAX19713 |
10-Bit, 45Msps, Full-Duplex, Analog Front-End |
Similar Products by Application
Evaluation Kits
Products with Similar Part Numbers
Didn't Find What You Need?
Information Index
Document Ref.: 19-0527
Rev 0;
2006-05-24
This page last modified: 2009-12-10
|
Download
E-Mail