MAX16031, MAX16032

EEPROM-Based System Monitors with Nonvolatile Fault Memory

EEPROM-Configurable Devices Maximize Uptime in High-Reliability Systems such as Network, Telecom, and Server Equipment

 Overview   Technical Documents   Ordering Info   Related Products   User Comments (0)   All   


Status Explanations for product status codes

Active: In Production.

Description

The MAX16031/MAX16032 EEPROM-configurable system monitors feature an integrated 10-bit analog-to-digital converter (ADC) designed to monitor voltages, temperatures, and current in complex systems. These EEPROM-configurable devices allow enormous flexibility in selecting operating ranges, upper and lower limits, fault output configuration, and operating modes with the capability of storing these values within the device.

The MAX16031 monitors up to eight voltages, three temperatures (one internal/two external remote temperature diodes), and a single current. The MAX16032 monitors up to six voltages and two temperatures (one internal/one remote temperature diode). Each of these monitored parameters is muxed into the ADC and written to its respective register that can be read back through the SMBus™ and JTAG interface.

Measured values are compared to the user-configurable upper and lower limits. For voltage measurements, there are two undervoltage and two overvoltage limits. For current and temperature, there are two sets of upper limits. Whenever the measured value is outside its limits, an alert signal is generated to notify the processor. Independent outputs are available for overcurrent, overtemperature, and undervoltage/overvoltage that are configured to assert on assigned channels. There are also undedicated fault outputs that are configured to offer a secondary limit for temperature, current, or voltage fault or provide a separate overvoltage output.

During a major fault event, such as a system shutdown, the MAX16031/MAX16032 automatically copy the internal ADC registers into the nonvolatile EEPROM registers that then are read back for diagnostic purposes.

The MAX16031/MAX16032 offer additional GPIOs that are used for voltage sequencing, additional fault outputs, a manual reset input, or read/write logic levels. A separate current-sense amplifier with an independent output allows for fast shutoff during overcurrent conditions. The MAX16031/MAX16032 are available in a 7mm x 7mm TQFN package and are fully specified from -40°C to +85°C.
 

Data Sheet

Download this datasheet in PDF formatDownload Rev 4 (PDF, 296.8kB)
Send this datasheet to any email addressE-Mail
An evaluation kit is available: MAX16031EVKIT

NOTE: This product uses the following:
MAX16031 EV Kit Software

Key Features

  • Supply Voltage Operating Range of 2.85V to 14V
  • Monitors Up to Eight Voltages (Single-Ended or Pseudo-Differential) with 1% Accuracy
  • EEPROM-Configurable Limits
    • Two Undervoltage and Two Overvoltage
    • Two Overtemperature
    • Two Overcurrent
  • High-Side Current-Sense Amplifier with Overcurrent Output (MAX16031 Only)
  • Monitors Up to Three Temperatures (1 Internal/2 Remote)
  • Nonvolatile Fault Memory Stores Fault Conditions for Later Retrieval
  • Two Additional Configurable Fault Outputs
  • Two Configurable GPIOs
  • SMBus/I²C-Compatible Interface with Active-Low ALERT Output and Bus Timeout Function
  • JTAG Interface
  • 7mm x 7mm, 48-Pin TQFN Package
 

Applications/Uses

  • Networking
  • Servers
  • Storage Systems
  • Telecom
  • Workstations
   

Diagram

MAX16031, MAX16032: Pin Configuration
Pin Configuration

Application Notes

Application Note 4283   In-Circuit Programming of the MAX16031/MAX16032 EEPROM-Based System Monitors
Application Note 4284   External Temperature Sensor Calibration for the MAX16031/MAX16032 System Monitors

Product Guides

Microprocessor Supervisory (PDF)

Reliability Reports

Reliability Report: MAX16031.pdf MAX16032.pdf
Show FIT data for:

Software/Models

MAX16031 EV Kit Software
MAX16031 BSDL Model

Ordering Information

Filters: Part Number: Package: Temperature: Tape and Reel Sample
Part Number Free
Sample
Buy Status Explanations for product status codes Package:
TYPE PINS FOOTPRINT
DRAWING  CODE/VAR *
Temp RoHS/Lead-Free?
Materials Analysis
MAX16031ETM+  
Active TQFN;48 pin;50.4 mm²
Outline Drawing:21-0144 (PDF)
Land Pattern: 90-0132 (PDF)
Use pkgcode/variation: T4877+6*
-40°C to +85°C RoHS/Lead-Free: Lead Free
Materials Analysis
MAX16031ETM+T    
Active TQFN;48 pin;50.4 mm²
Outline Drawing:21-0144 (PDF)
Land Pattern: 90-0132 (PDF)
Use pkgcode/variation: T4877+6*
-40°C to +85°C RoHS/Lead-Free: Lead Free
Materials Analysis
MAX16032ETM+  
Active TQFN;48 pin;50.4 mm²
Outline Drawing:21-0144 (PDF)
Land Pattern: 90-0132 (PDF)
Use pkgcode/variation: T4877+6*
-40°C to +85°C RoHS/Lead-Free: Lead Free
Materials Analysis
MAX16032ETM+T    
Active QFN;

Land Pattern: Not Available

-40°C to +85°C See data sheet

Notes:
  1. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
  2. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day.
  3. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt; -D = drypack; -U/+U on DS parts = cut tape. More: See Full Data Sheet or Maxim Product Naming Conventions.
  4. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product uses. Note that "+", "#", "-" in the part number suffix describes RoHS status. Package drawings may show a different suffix character.

Evaluation Kits

MAX16031EVKIT Evaluation Kit for the MAX16031

Products with Similar Part Numbers

MAX16031EVKIT Evaluation Kit for the MAX16031

More Information

New Product Press Release 2007-11-01 ]


Didn't Find What You Need?

Information Index

Document Ref.: 19-0870 Rev 4; 2011-10-18
This page last modified: 2011-10-18


 


Contact Us     |     Privacy Policy     |     Legal Notices
Copyright © 2012 by Maxim Integrated Products