Maxim > Products > Sensors > MAX6638
Maxim > Products > Thermal Management > MAX6638

MAX6638

Temperature Monitor with Dual Serial Interface

 Overview   Technical Documents   Ordering Info   Related Products   User Comments (0)   All   


Status Explanations for product status codes

All versions are No Longer Available.

Description

The MAX6638 thermal-management sensor includes internal (local) and external (remote) digital temperature sensors and two independent SMBus™ serial ports. The remote temperature accuracy is ±1.0°C and the local temperature accuracy is ±2°C. The MAX6638 also features extended temperature resolution data available in 0.125°C increments.

The MAX6638 provides three system alarms: channel 1 alert (active-low ALERT1), overtemperature (active-low OVERT1), and channel 2 alert (active-low ALERT2) that contain programmable thresholds set independently by each of the SMBus serial ports (SMBus1 and SMBus2). Each alert output asserts when any of four temperature conditions is violated: local overtemperature, remote overtemperature, local undertemperature, or remote undertemperature. The overtemperature signal asserts when the temperature rises above the value in the overtemperature limit register. Use the active-low OVERT1 output to activate a cooling fan or trigger a system shutdown.

Each of the 2-wire serial-interface ports accepts standard System Management Bus (SMBus) write byte, read byte, send byte, and receive byte commands independently of one another with total collision avoidance handled by the MAX6638. Each SMBus can operate its own unique serial-data rate to access any register in the MAX6638 for data reads or data writes. The MAX6638 manages all dual-port data register access functions providing a seamless, conflict-free, integration into a multimaster architecture for thermal management.

The MAX6638 performs measurements autonomously, at the programmed conversion rate, or in a single-conversion mode. Each SMBus port can set the conversion rate with the higher conversion and update rate dominating the average power-supply current. Single-conversion requests have a maximum delay of two conversion cycles with channel-conversion management and cycling regulated by the dual-port controller.

The MAX6638 operating temperature range is -40°C to +125°C and measures temperatures between 0°C and +145°C. The MAX6638 is available in a 16-pin, 4mm x 4mm TQFN with exposed paddle package.

 

Data Sheet

Download this datasheet in PDF formatDownload Rev 1 (PDF, 316kB)
Send this datasheet to any email addressE-Mail

Key Features

  • Two Independent SMBus/I²C-Compatible Interfaces with Collision Avoidance
  • High Accuracy ±1.0°C from +85°C to +100°C (Remote)
  • Remote and Local Temperature Measurements
  • Three Programmable Output Alarms: Active-Low ALERT1, Active-Low OVERT1, Active-Low ALERT2
  • Programmable Conversion Rates
  • 11-Bit Low-Noise Integrating ADC
  • No Calibration Required
  • Autoscan Conversions
 

Applications/Uses

  • Computer Motherboard Systems
  • Desktop Computers
  • Graphics Cards
  • Notebook Computers
  • Workstations
   

Diagram

MAX6638: Typical Operating Circuit
Typical Operating Circuit

Application Notes

Tutorial 4679   Thermal Management Handbook

Reliability Reports

Show FIT data for:
Request Reliability Report for:

Software/Models

none

Ordering Information

Filters: Part Number: Package: Temperature: Tape and Reel Sample
Part Number Free
Sample
Buy Status Explanations for product status codes Package:
TYPE PINS FOOTPRINT
DRAWING  CODE/VAR *
Temp RoHS/Lead-Free?
Materials Analysis
MAX6638ATE     N/A No Longer Available TQFN;16 pin;16.8 mm²
Outline Drawing:21-0139 (PDF)
Land Pattern: 90-0070 (PDF)
Use pkgcode/variation: T1644-4*
-40°C to +125°C RoHS/Lead-Free: No
Materials Analysis
MAX6638ATE-T     N/A No Longer Available QFN;16 pin

Land Pattern: Not Available

-40°C to +125°C See data sheet
MAX6638EVKIT     N/A No Longer Available KIT;

Land Pattern: Not Available

See data sheet

Notes:
  1. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.
  2. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day.
  3. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt; -D = drypack; -U/+U on DS parts = cut tape. More: See Full Data Sheet or Maxim Product Naming Conventions.
  4. * Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product uses. Note that "+", "#", "-" in the part number suffix describes RoHS status. Package drawings may show a different suffix character.

Similar Products by Application

Computers: Desktops and Workstations > Thermal Management

More Information

New Product Press Release 2006-09-05 ]


Didn't Find What You Need?

Information Index

Document Ref.: 19-3895 Rev 1; 2006-08-17
This page last modified: 2010-05-27


 


Contact Us     |     Privacy Policy     |     Legal Notices
Copyright © 2012 by Maxim Integrated Products