Abstract: The 1-Wire standard established in 1989 has been upgraded to accommodate noisy and long-line 1-Wire networks. This application note explains the new standard enhancements, and shows how to make a 1-Wire master that works with both standard and new devices.
Introduction
The 1-Wire bus is a simple signaling scheme that performs two-way communication over a single electrical connection. In any 1-Wire system, there is a single master and one or more slave devices sharing a common data line. Dallas Semiconductor created the 1-Wire standard in 1989 to reduce the contacts for portable data-carrying modules. The result of this were iButtons®, the 16mm battery-shaped modules that have sold > 130 million worldwide.
The 1-Wire scheme also enabled other applications such as chip-based tagging and long-line sensor applications. The original 1-Wire front-end did not, however, anticipate the noise levels and line characteristics (e.g., line length) of some of these new applications. Satisfying these new application demands often challenged a 1-Wire implementation in the field. Therefore, to accommodate these applications a new 1-Wire front-end called the 1-Wire Extended Network Standard was developed, and incorporated into several new devices. Table 1 lists 1-Wire devices and shows which are supported by the new extended standard.
Important Features of the New Extended Standard
Noise from various sources can result in signal glitching on the 1-Wire line. The noise can come from reflections from network endpoints or branch points. (For more information, please see application note 148, "Guidelines for Reliable 1-Wire Networks.") Noise can also come from an external source and get coupled onto the 1-Wire signal. A noise glitch during the rising edge can cause the 1-Wire device to become unsynchronized with the master. The improvements to the extended network front-end address these rising edge issues.
The new 1-Wire front-end incorporates three main components: a lowpass filter for high-frequency noise, voltage hysteresis on low-to-high switching, and a rising-edge hold-off time. Some 1-Wire devices also have slew control on the presence pulse. Figure 1 illustrates these features. The shaded pink regions show how the device ignores glitches in voltage magnitude and over a period of time during 1-Wire low-to-high transitions.
Figure 1. New 1-Wire front-end features.
Table 1. 1-Wire Devices
Device
FC
Description
1-Wire Extended Network Support
DS1425*
02
Multikey iButton, 1152-bit secure memory
DS1427*
04
4k NV RAM memory and clock, timer, alarms
DS1820
10
Temperature and alarm trips
DS1822
22
1-Wire Econo temp sensor
DS1825
3B
1-Wire thermometer with 4-bit address
DS18B20
28
Adjustable resolution temperature
DS18S20
10
Temperature and alarm trips
DS1982
09
1k EPROM memory
DS1985
0B
16k EPROM memory
DS1986
0F
64k EPROM memory
DS1904
24
Real-Time Clock (RTC) iButton
DS1920
10
Temperature and alarm trips
DS1921G DS1921H DS1921Z
21
Thermochron temperature logger
DS1922L DS1922T DS1923
41
High-Capacity Thermochron and/or Hygrochron. temperature and/or humidity dataloggers, respectively
√
DS1961S
33
1k EEPROM memory with SHA-1 engine
DS1963L*
1A
4k NV RAM memory with write cycle counters
DS1963S
18
4K NVRAM memory and SHA-1 engine
DS1971
14
256-bit EEPROM memory and 64-bit OTP register
DS1972
2D
1k EEPROM memory
√
DS1973
23
4k EEPROM memory
DS1977
37
Password-protected 32kB (bytes) EEPROM
√
DS1990A DS1990R
01
1-Wire address only
DS1991*
02
Multikey iButton, 1152-bit secure memory
DS1992
08
1k NV RAM memory
DS1993
06
4k NV RAM memory
DS1994*
04
4k NV RAM memory and clock, timer, alarms
DS1995
0A
16k NV RAM memory
DS1996
0C
64k NV RAM memory
DS2401
01
1-Wire address only
DS2405
05
Single switch
DS2404*
04
4k NV RAM memory and clock, timer, alarms
DS2406
12
1k EPROM memory, 2-channel addressable switch
DS2408
29
8-channel addressable switch
√
DS2409*
1F
Dual switch, coupler
DS2411
01
Low-voltage, unique 64-bit serial ROM number (requires VDD connection)
√
DS2413
3A
Dual-channel addressable switch
√
DS2415
24
RTC
DS2417
27
RTC with interrupt
DS2422
41
High-capacity Thermochron/Hygrochron (temperature and humidity) datalogger
√
DS2423*
1D
4k NV RAM memory with external counters
DS2430A*
14
256-bit EEPROM memory and 64-bit OTP register
DS2431
2D
1024-bit EEPROM memory
√
DS2432
33
1k EEPROM memory with SHA-1 engine
DS2433
23
4k EEPROM memory
DS2436
1B
1-Wire battery ID with temperature and voltage monitor
DS2438
26
Temperature, ADC
DS2450
20
Quad ADC
DS2502
09
1k EPROM memory
DS2505
0B
16k EPROM memory
DS2506
0F
64k EPROM memory
DS2720
31
1-Wire single-cell Lithium recharger with protection
*This device is no longer recommended for new designs.
Note: New 1-Wire devices are constantly added to the product line. Newer parts may not be in this list. Look for an 'Improved Network Behavior' section in the device's data sheet to see if the device incorporates the new extended network front-end.
The new features in the Extended Network Standard are only fully active during standard speed communication, not in overdrive. Adding these features to the 1-Wire front-end can affect the 1-Wire timing specification. Specifically, the new standard introduces an EC table parameter, tREH, that represents the rising-edge hold-off time. This hold-off behavior increases the low time generated by the master and required in a read bit, tRL. See Table 2.
Field experience with applications using long lines to communicate with 1-Wire devices demonstrates the importance of adequate recovery between bits. As a result, all of the extended-network devices have longer recovery times, tREC. The recovery-time specification for all devices (standard and extended network) is given for one device on a 1-Wire bus. For a guide to extending this specification to multiple devices, see application note 3829, "Determining the Recovery Time for Multiple-Slave 1-Wire Networks."
Devices that incorporate slew control on the presence pulse include a parameter, tFPD, for Presence Detect Fall Time. While controlling the slew creates less reflections on long lines, it has a significant effect on the window in which a master can detect the presence pulse. Impedance matching on the 1-Wire master can be equally effective in controlling these reflections without incurring the slew-rate delay. Consequently, future devices may not incorporate the presence-pulse slew-rate feature.
Table 2. EC Table Differences
Parameter
Speed
Min/Max
Standard
Extended Network
tREC
Standard
Min
1
5
Overdrive
Min
1
2
tREC (before reset)
Overdrive
Min
1
5
tREH
Standard
Min
—
0.5
Standard
Max
—
5
Overdrive
Min
—
0.5
Overdrive
Max
—
5
tRL
Standard
Min
1
5
Summary
A 1-Wire master can work with both standard and extended-network devices. Accommodating the extended-network devices is as simple as extending recovery time between bits and using a longer start pulse for a read bit, tRL. While the longer recovery will slow the throughput, the change in the read-bit start pulse will not affect the throughput. For networks with devices using presence-pulse slew control, tFPD, care must be taken to select the sample point for the presence pulse. For some devices and voltages the sample range may be restrictive.
Application note 126, "1-Wire Communication Through Software" describes a simple 1-Wire master with timing that is already compatible with standard and extended-network devices. The application note includes an Excel spreadsheet for customizing the parameters based on the 1-Wire slave devices and the network conditions such as rise time. Download the Excel sheet here: http://files.dalsemi.com/auto_id/public/an126.zip.
Automatic Updates
Would you like to be automatically notified when new application notes are published in your areas of interest? Sign up for EE-Mail™.
Download, PDF Format
