Abstract: Application note 374 describes the hardware and software considerations when upgrading an existing DS21x5y design to use the DS2155 device. The Dallas Semiconductor DS2155 T1/E1/J1 single chip transceiver (SCT) has a broader feature set and as such the designer must make changes in software and hardware when migrating to the DS2155 from the DS21x5y device. Any designer who is thinking of upgrading an existing design to use the DS2155 should read this application note. The application note contains detailed information for software migration such as: register location changes, how individual functions have changed from the DS21x5y to the DS2155, and which new functions are available on the DS2155. It also covers migration for the hardware interface and covers topics such as: interfacing with other devices, changes to the line interface, and new functions that are available in the DS2155. In the end, the designer should have enough information to easily migrate an existing design which uses the DS21x5y to the DS2155 device. This note uses the device number DS21x52 to refer to both the DS21352 and DS21552. Also, references to DS21x54 will correspond to both the DS21354 and DS21554. Whenever DS21x5y is used, it refers to all the parts mentioned above. 1. Overview The DS2155 is a software selectable T1, J1 or E1 Single Chip Transceiver (SCT) for short and long haul applications. This application note intends to highlight many of the differences between the DS2155 and the previous family of Dallas Semiconductor's SCTs. While, the DS2155 is pin compatible with previous Dallas Semiconductor SCT's (DS2152/54, DS21352/552, & DS21552/554) the register set for the device is much more complex. In the following pages, we will identify features from the DS21x5y devices and pinpoint their register locations in the DS2155. Additionally, some of the new features available in the DS2155 and what provisions need to be made existing DS21x5y designs or new designs in order to use the DS2155 will be discussed. This note is broken into 4 sections. First, the location of DS21x52 (T1) and DS21x54 (E1) features will be linked to the DS2155 register map. The note will then discuss some of the new features that are available to users in all modes of operation. The last section deals with hardware considerations when using the DS2155. 1.1 Contents Software Considerations: DS2155 vs. DS21x52 (T1) ID Register Receive Control Registers Transmit Control Registers Common Control Registers Status and Information Registers Error Count Registers DS0 Monitoring Function Registers Signaling Registers Per-Channel Code (Idle) Generation Registers Channel Blocking Registers HDLC Registers Line Interface, Programmable In-Band Loop Code, and Transmit Transparency Registers Interleaved PCM Bus Operation Register Software Considerations: DS2155 vs. DS21x54 (E1) ID Register Receive Control Registers Transmit Control Registers Common Control Registers Status and Information Registers Error Count Registers DS0 Monitoring Function Registers Signaling Registers Per-Channel Code (Idle) Generation Registers Channel Blocking Registers Additional (Sa) and International (Si) Bit Operation Registers HDLC Registers Line Interface Control Register Interleaved PCM Bus Operation Register New DS2155 Features Key Additional Features in the DS2155 High Throughput Features in the DS2155 Hardware Considerations: DS2155 vs. DS21x5y Reassigned Pin Functions for Pins 36, 54, and 76 New Feature for Pin 3 New Feature for Pin 14 Receive and Transmit Termination New User Output Pins in the DS2155 1.2 How to Read the Register Mapping Tables This note will discuss each register of the DS21x52 and DS21x54 SCTs. In some cases the entire register has been kept intact, but has been relocated to a new address. For these cases the new address of the register in the DS2155 along with the DS2155 register abbreviation will be listed. In other cases, single bits from the registers have been relocated to different address. If a bit has been relocated, the DS21x5y register will be presented in the following manner. First, two lines identifying the DS21x5y registers abbreviation, name and hexadecimal address will be given, followed by a register table consisting of 4 rows will follow. The first row of the register table will always be the same and will identify the control bit position in the DS21x5y register. Row 2 will contain the control bit name within the DS21x5y register. The last 2 rows in the register table identify where to find the control bit in the DS2155. Row 3 provides the user with the DS2155's abbreviated register name where the control bit can be found. The last row gives the address and bit number of the new location. For example, a bit that has been relocated in the DS2155 to bit position 3 in the register at the location of address A5 Hex would have the value A5.3 placed in the 55 Addr.Bit row. DS21x5y Register: RE: Register Example DS21x5y Register Address: xx Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 B7 NEWREG addr.bit 6 B6 NEWREG addr.bit 5 B5 NEWREG addr.bit 4 B4 NEWREG addr.bit 3 B3 NEWREG addr.bit 2 B2 NEWREG addr.bit 1 B1 NEWREG addr.bit 0 B0 NEWREG addr.bit If the functionality and/or name of the control bit has changed or if additional information is required, it will be indicated by an * in the register table. The additional information for these control bits will be presented below the register table. 2. Software Considerations: DS2155 vs. DS21x52 (T1) This section will present the registers for the DS21352 and DS21552. The registers are presented in the order that they appear in the DS21352 and DS21552 data sheet. ID Register DS21x52 Register: IDR: Device Identification Register DS21x52 Register Address: 0F Hex The Device Identification Register (IDR) for the DS2155 is located at the same address as the IDR for the DS21x52. The upper four bits display the DS2155 ID (1011) and the lower four bits display the die revision. Receive Control Registers DS21x52 Register: RCR1: Receive Control Register 1 DS21x52 Register Address: 2B Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LCVCRF ERCNT 41.0 6 ARC T1RCR1 03.6 5 OOF1 T1RCR1 03.5 4 OOF2 T1RCR1 03.4 3 SYNCC T1RCR1 03.3 2 SYNCT T1RCR1 03.2 1 SYNCE T1RCR1 03.1 0 RESYNC T1RCR1 03.0 DS21x52 Register: RCR2: Receive Control Register 2 DS21x52 Register Address: 2C Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RCS See below See below 6 RZBTSI T1RCR2 04.2 5 RSDW IOCR1 01.6* 4 RSM IOCR1 01.5* 3 RSIO IOCR1 01.4 2 RD4YM T1RCR2 04.0 1 FSBE ERCNT 41.2 0 MOSCRF ERCNT 41.1 RSM, bit 4, has been renamed as RSMS1. There is no new functionality associated with the bit. RSDW, bit 5, has been renamed as RSMS2. There is no new functionality associated with the bit. RCS, bit 7, was used to generate either a 7F idle code or the digital milliwatt pattern. In the DS2155, the digital milliwatt pattern is generated using the T1RDMR1 (0C Hex), T1RDMR2 (0D Hex), and T1RDMR3 (0E Hex) registers. See section 10.1 of the DS2155 data sheet for more information on generating the digital milliwatt pattern. Idle code generation has changed in the DS2155. See section 18 of the DS2155 data sheet for more information. Transmit Control Registers DS21x52 Register: TCR1: Transmit Control Register 1 DS21x52 Register Address: 35 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LOTCMC CCR1 See below 6 TFPT T1TCR1 05.6 5 TCPT T1TCR1 05.5 4 TSSE T1TCR1 05.4 3 GB7S T1TCR1 05.3 2 TFDLS T1TCR1 05.2 1 TBL T1TCR1 05.1 0 TYEL T1TCR1 05.0 LOTCMC, bit 7, has been combined with other functions to simplify the selection of the transmit clock source. The two bits, Transmit Clock Source Select 0 (TCSS0) and Transmit Clock Source Select 1 (TCSS1), are located in the DS2155's Common Control Register 1 (CCR1, address 70 Hex) in bit positions 1 and 2 respectively. DS21x52 Register: TCR2: Transmit Control Register 2 DS21x52 Register Address: 36 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 TEST1 MSTRREG 00.3 6 TEST0 MSTRREG 00.2 5 TZBTSI T1TCR2 06.1 4 TSDW IOCR1 01.3 3 TSM IOCR1 01.2 2 TSIO IOCR1 01.1 1 TD4YM T1TCR2 06.2 0 TB7ZS T1TCR2 06.0 Common Control Registers DS21x52 Register: CCR1: Common Control Register 1 DS21x52 Register Address: 37 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 TESE ESCR 4F.4 6 ODF IOCR1 01.0 5 RSAO PCPR 28.7* 4 TSCLKM IOCR2 02.1 3 RSCLKM IOCR2 02.0 2 RESE ESCR 4F.0 1 PLB LBCR 4A.1 0 FLB LBCR 4A.0 RSAO, bit 5, has been renamed as RSAOICS and been placed in the Per-Channel Pointer Register. In the DS21x52, setting the RSAO bit would force all of the extracted robbed-bit signaling positions to one. If the user wished to invoke this option on a per-channel basis, the RPCSI control bit in CCR4.6 and the receive channel blocking registers had to be set accordingly. In the DS2155, the user sets the RSAOICS bit and then selects, via the Per-Channel Data Register 1-3, the channels in which to force the robbed-bit signaling bits to one. See section 7 of the DS2155 data sheet for more information on per-channel operation. DS21x52 Register: CCR2: Common Control Register 2 DS21x52 Register Address: 38 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 TFM T1CCR1 07.2 6 TB8ZS T1TCR2 06.7 5 TSLC96 T1TCR2 06.6 4 TFDL T1TCR2 06.5* 3 RFM T1RCR2 04.6 2 RB8ZS T1RCR2 04.5 1 RSLC96 T1RCR2 04.4 0 RZSE T1RCR2 04.3 TFDL, bit 4, has been renamed as TZSE. No additional functionality has been associated with this bit. DS21x52 Register: CCR3: Common Control Register 3 DS21x52 Register Address: 30 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RESMDM ESCR 4F.1 6 TCLKSRC CCR1 See Below 5 RLOSF CCR1 70.0 4 RSMS IOCR1 01.7 3 PDE T1CCR1 07.1 2 ECUS ERCNT 41.5 1 TLOOP T1CCR1 07.0 0 TESMDM ESCR 4F.5 TCLKSRC, bit 6, has been combined with other functions to simplify the selection of the transmit clock source. Two bits, Transmit Clock Source Select bit 0 (TCSS0) and bit 1 (TCSS1) are located in the DS2155's Common Control Register 1 (CCR1, address 70 Hex) in bit positions 1 and 2 respectively. DS21x52 Register: CCR4: Common Control Register 4 DS21x52 Register Address: 11 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RSRE PCPR 28.6* 6 RPCSI See Below See Below 5 RFSA1 See Below See Below 4 RFE SIGCR 40.4 3 RFF SIGCR 40.3 2 THSE PCPR 28.3* 1 TPCSI See Below See Below 0 TIRFS See Below See Below Control bit 0, TIRFS, has been incorporated in the new functionality for idle code generation. See section 18 of the DS2155 data sheet for more detail. Control bit 1, TPCSI, has been incorporated into the per-channel register operation. See sections 7 and 17 of the DS2155 data sheet for additional information. THSE, bit 2, has been renamed as THSCS. See sections 7 and 17 of the DS2155 data sheet for information on per-channel register operation. RFSA, control bit 5, has been incorporated into the per-channel register function. The user sets the BTCS bit in the PCPR register and selects the channels which are to be forced to one by writing to the PCDR1-PCDR3 registers. See sections 7 and 17 of the DS2155 data sheet for additional information. RPCSI, bit 6, has been incorporated into the per-channel register function. See sections 7 and 17 of the DS2155 data sheet for additional information. RSRE, bit 7, has been renamed as RSRCS. See sections 7 and 17 of the DS2155 data sheet for additional information on receive signaling re-insertion. DS21x52 Register: CCR5: Common Control Register 5 DS21x52 Register Address: 19 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 TJC T1TCR1 05.7 6 LLB LBCR 4A.3 5 LIAIS LIC2 79.4* 4 TCM4 TDS0SEL 74.4 3 TCM3 TDS0SEL 74.3 2 TCM2 TDS0SEL 74.2 1 TCM1 TDS0SEL 74.1 0 TCM0 TDS0SEL 74.0 LIAIS, bit 5, has been renamed as TUA1. No additional functionality has been associated with this bit DS21x52 Register: CCR6: Common Control Register 6 DS21x52 Register Address: 1E Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RJC T1RCR2 04.1 6 RESA ESCR 4F.3* 5 TESA ESCR 4F.7* 4 RCM4 RDS0SEL 76.4 3 RCM3 RDS0SEL 76.3 2 RCM2 RDS0SEL 76.2 1 RCM1 RDS0SEL 76.1 0 RCM0 RDS0SEL 76.0 TESA, bit 5, has been renamed as TESALGN. There is no new functionality associated with the bit. RESA, bit 6, has been renamed as RESALGN. There is no new functionality associated with the bit. DS21x52 Register: CCR7: Common Control Register 7 DS21x52 Register Address: 0A Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LIRST LIC2 79.6 6 RLB LBCR 4A.2 5 RESR ESCR 4F.2 4 TESR ESCR 4F.6 3 - - - 2 LIUSI LIC3 7A.2* 1 CDIG LIC3 7A.0* 0 LIUODO LIC2 79.0* LIUODO, bit 0, has been renamed as CLDS. In the DS21x52, this bit determined whether the TTIP and TRING outputs would be open drain or not. In the DS2155, setting this bit to a one will redefine the operation of the transmit line driver. When this bit is set to a one and LIC1.5 = LIC1.6 = LIC1.7 = 0, then the device will generate a square wave at the TTIP and TRING outputs instead of a normal waveform. When this bit is set to a one and LIC1.5 = LIC1.6 = 0 and LIC1.7 = 1, then the device will force TTIP and TRING outputs to become open drain drivers instead of their normal push-pull operation. This bit should be set to zero for normal operation of the DS2155. CDIG, bit 1, has been renamed as TAOZ. There is no new functionality associated with the bit. LIUSI, bit 2, has been renamed as RSCLKE. There is no new functionality associated with the bit. However, there is now a TSCLKE control bit available in the DS2155, which controls G.703 support for the transmitter. Status and Information Registers DS21x52 Register: RIR1: Receive Information Register 1 DS21x52 Register Address: 22 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 COFA INFO1 10.5 6 8ZD INFO1 10.4 5 16ZD INFO1 10.3 4 RESF SR5 1E.2 3 RESE SR5 1E.1* 2 SEFE INFO1 10.2 1 B8ZS INFO1 10.1 0 FBE INFO1 10.0 RESE, bit 3, has been renamed as RESEM. There is no new functionality associated with this bit. DS21x52 Register: RIR2: Receive Information Register 2 DS21x52 Register Address: 31 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RLOSC SR2 18.4 6 LRCLC SR2 18.5* 5 TESF SR5 1E.5 4 TESE SR5 1E.4* 3 TSLIP SR5 1E.3 2 RBLC SR2 18.6* 1 RPDV INFO1 10.7 0 TPDV INFO1 10.6 RBLC, bit 2, has been renamed as RUA1C. There is no new functionality associated with this bit. TESE, bit 4, has been renamed as TESEM. There is no new functionality associated with this bit. LRCLC, bit 6, has been replaced by RCLC in the DS2155. The functionality of the bit is the same. The difference is where the clear criteria is monitored. In the DS21x52, the bit was monitoring RTIP/RRING for the clear criteria. In the DS2155, the RCLC bit is cleared based on data into the framer, not the line interface. DS21x52 Register: RIR3: Receive Information Register 3 DS21x52 Register Address: 10 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RL1 INFO2 See Below 6 RL0 INFO2 See Below 5 JALT SR1 16.4 4 LORC SR3 1A.3 3 FRCL SR2 18.1* 2 - - - 1 - - - 0 - - - FRCL, bit 3, has been renamed as RCL. There is no new functionality associated with this bit. RL0, bit 6, and RL1, bit 7, have been replaced by additional monitoring capabilities. The DS2155 will report the signal strength at RTIP and RRING in 2.5dB increments via RL3-RL0 located in Information Register 2 (INFO2, address = 11 Hex ). This feature is helpful when trouble shooting line performance problems. DS21x52 Register: SR1: Status Register 1 DS21x52 Register Address: 20 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LUP SR3 1A.5 6 LDN SR3 1A.6 5 LOTC SR3 1A.4 4 RSLIP SR5 1E.0 3 RBL SR2 18.2* 2 RYEL SR2 18.3 1 LRCL SR1 16.3 0 RLOS SR2 18.0 RBL, bit 3, has been renamed as RUA1. There is no new functionality associated with this bit. DS21x52 Register: SR2: Status Register 2 DS21x52 Register Address: 21 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RMF SR4 1C.2 6 TMF SR4 1C.4 5 SEC SR1 16.6* 4 RFDL SR8 24.3* 3 TFDL SR8 24.2* 2 RMTCH SR8 24.1 1 RAF SR8 24.4* 0 RSC SR1 16.5* RSC, bit 0, has been renamed as RSCOS. In the DS21x52, this bit was set when the DS21x52 detected a change of state in ANY of the robbed-bit signaling bits. The DS2155 allows the user to select the channels that will be monitored. Via the Receive Signaling Change Of State Interrupt Enable Registers (RSCSE through RSCSE4), the user can select the channels in which a change of state in the robbed-bit signaling bits will set this status bit. RAF, bit 1, has been renamed as RFDLAD. There is no new functionality associated with this bit. TFDL, bit 3, has been renamed as TFDLE. There is no new functionality associated with this bit. RFDL, bit 4, has been renamed as RFDLF. There is no new functionality associated with this bit. SEC, bit 5, has been renamed as TIMER. In the DS21x52, this bit was set on increments of one second (referenced to RCLK). In the DS2155, this bit follows the error counter update interval as determined by the ECUS bit in the Error Counter Configuration Register (ERCNT). In T1 mode, this bit can be configured to set on increments of 1 second or 42ms (referenced to RCLK). DS21x52 Register: IMR1: Interrupt Mask Register 1 DS21x52 Register Address: 7F Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LUP IMR3 1B.5 6 LDN IMR3 1B.6 5 LOTC IMR3 1B.4 4 SLIP IMR5 1F.0* 3 RBL IMR2 19.2* 2 RYEL IMR2 19.3 1 LRCL IMR1 17.3 0 RLOS IMR2 19.0 RBL, bit 3, has been renamed as RUA1. There is no new functionality associated with this bit. SLIP, bit 2, has been renamed as RSLIP. There is no new functionality associated with this bit. DS21x52 Register: IMR2: Interrupt Mask Register 2 DS21x52 Register Address: 6F Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RMF IMR4 1D.2 6 TMF IMR4 1D.4 5 SEC IMR1 17.6* 4 RFDL IMR8 25.3* 3 TFDL IMR8 25.2* 2 RMTCH IMR8 25.1 1 RAF IMR8 25.4* 0 RSC IMR1 17.5* RSC, bit 0, has been renamed as RSCOS. In the DS21x52, this bit would enable the device to generate an interrupt when the DS21x52 detected a change of state in ANY of the robbed-bit signaling bits. The DS2155 allows the user to select the channels that will be monitored. Via the Receive Signaling Change Of State Interrupt Enable Registers (RSCSE through RSCSE4), the user can select the channels in which a change of state in the robbed-bit signaling bits will generate an interrupt provided the RSCOS bit is set by the user. RAF, bit 1, has been renamed as RFDLAD. There is no new functionality associated with this bit. TFDL, bit 3, has been renamed as TFDLE. There is no new functionality associated with this bit. RFDL, bit 4, has been renamed as RFDLF. There is no new functionality associated with this bit. SEC, bit 5, has been renamed as TIMER. In the DS21x52, this bit enabled the interrupt on increments of one second (referenced to RCLK). In the DS2155, this bit follows the error counter update interval as determined by the ECUS bit in the Error Counter Configuration Register (ERCNT). In T1 mode, this bit can be configured to interrupt on increments of 1 second or 42ms (referenced to RCLK). Error Count Registers The error count registers have been kept intact, but have been relocated. In addition, the Path Code Violation Count Register 1 and the Multiframes Out Of Sync Count Register 1 no longer share a common address and therefore are both 16-bit counters. See section 15 in the DS2155 data sheet for additional information on the error count registers. DS21x52 Registers: LCVCR1, LCVCR2: Line Code Violation Count Register 1 & 2 DS21x52 Register Address: 23 Hex, 24 Hex DS21x52 Registers: PCVCR1, PCVCR2: Path Code Violation Count Register 1 & 2 DS21x52 Register Address: 25 Hex (Same as MOSCR1), 26 Hex DS21x52 Register: MOSCR1, MOSCR2: Multiframes Out Of Sync Count Register 1 & 2 DS21x52 Register Address: 25 Hex (Same as PCVCR1), 27 Hex DS21x52 Register DS21x52 Register Abbreviation DS2155 Register Abbreviation DS2155 Address (Hex) Line Code Violation Count Register 1 LCVCR1 (23 Hex) LCVCR1 42 Line Code Violation Count Register 2 LCVCR2 (24 Hex) LCVCR2 43 Path Code Violation Count Register 1 PCVCR1 (25 Hex)* PCVCR1 44 Path Code Violation Count Register 1 PCVCR2 (26 Hex) PCVCR2 45 Multiframes Out Of Sync Count Register 1 MOSCR1 (25 Hex)* FOSCR1 46 Multiframes Out Of Sync Count Register 2 MOSCR2 (27 Hex) FOSCR2 47 In the DS21x52, PCVCR1 and MOSCR1 shared the count register located at address 25 Hex. The two error counters no longer share a register in the DS2155. DS0 Monitoring Function Registers Both the Transmit DS0 Monitor Register and Receive DS0 Monitor Register has been relocated to a new address. DS21x52 Register: TDS0M: Transmit DS0 Monitor Register DS21x52 Register Address: 1A Hex DS21x52 Register: RDS0M: Receive DS0 Monitor Register DS21x52 Register Address: 1F Hex DS21x52 Register DS21x52 Register Abbreviation DS2155 Register Abbreviation DS2155 Address (Hex) Transmit DS0 Monitor Register TDS0M (1A Hex) TDS0M 75 Receive DS0 Monitor Register RDS0M (1F Hex) RDS0M 77 Signaling Registers Receive Signaling Registers 1 through 12 can be found at the same address. However, the signaling information contained in the signaling registers has been rearranged. See section 17 of the DS2155 data sheet for additional information on signaling operation. DS21x52 Register: RS1 to RS12: Receive Signaling Registers DS21x52 Register Address: 60 to 6B Hex Receive Signaling Registers 1 through 12 can be found at the same address. In the ESF framing mode, there can be up to four signaling bits per channel (A, B, C, and D). In the D4 framing mode, there are only two signaling bits per channel (A and B). In the D4 framing mode, the framer will replace the C and D signaling bit positions with the A and B signaling bits from the previous multiframe. Hence, whether the framer is operated in either framing mode, the user needs only to retrieve the signaling bits every 3 ms. The Receive Signaling Registers are frozen and not updated during a loss of sync condition (SR2.0 = 1). They will contain the most recent signaling information before the "OOF" occurred. The following table shows the new the arrangement for the Receive Signaling Registers. In T1 mode, RS13-RS16 are not used. Transmit Signaling Registers (T1 Mode, ESF Format) Register Name DS2155 Address   (MSB)             (LSB) TS1 50 CH2-A CH2-B CH2-C CH2-D CH1-A CH1-B CH1-C CH1-D TS2 51 CH4-A CH4-B CH4-C CH4-D CH3-A CH3-B CH3-C CH3-D TS3 52 CH6-A CH6-B CH6-C CH6-D CH5-A CH5-B CH5-C CH5-D TS4 53 CH8-A CH8-B CH8-C CH8-D CH7-A CH7-B CH7-C CH7-D TS5 54 CH10-A CH10-B CH10-C CH10-D CH9-A CH9-B CH9-C CH9-D TS6 55 CH12-A CH12-B CH12-C CH12-D CH11-A CH11-B CH11-C CH11-D TS7 56 CH14-A CH14-B CH14-C CH14-D CH13-A CH13-B CH13-C CH13-D TS8 57 CH16-A CH16-B CH16-C CH16-D CH15-A CH15-B CH15-C CH15-D TS9 58 CH18-A CH18-B CH18-C CH18-D CH17-A CH17-B CH17-C CH17-D TS10 59 CH20-A CH20-B CH20-C CH20-D CH19-A CH19-B CH19-C CH19-D TS11 5A CH22-A CH22-B CH22-C CH22-D CH21-A CH21-B CH21-C CH21-D TS12 5B CH24-A CH24-B CH24-C CH24-D CH23-A CH23-B CH23-C CH23-D Transmit Signaling Registers (T1 Mode, D4 Format) Register Name DS2155 Address   (MSB)             (LSB) TS1 50 CH2-A CH2-B CH2-A CH2-B CH1-A CH1-B CH1-A CH1-B TS2 51 CH4-A CH4-B CH4-A CH4-B CH3-A CH3-B CH3-A CH3-B TS3 52 CH6-A CH6-B CH6-A CH6-B CH5-A CH5-B CH5-A CH5-B TS4 53 CH8-A CH8-B CH8-A CH8-B CH7-A CH7-B CH7-A CH7-B TS5 54 CH10-A CH10-B CH10-A CH10-B CH9-A CH9-B CH9-A CH9-B TS6 55 CH12-A CH12-B CH12-A CH12-B CH11-A CH11-B CH11-A CH11-B TS7 56 CH14-A CH14-B CH14-A CH14-B CH13-A CH13-B CH13-A CH13-B TS8 57 CH16-A CH16-B CH16-A CH16-B CH15-A CH15-B CH15-A CH15-B TS9 58 CH18-A CH18-B CH18-A CH18-B CH17-A CH17-B CH17-A CH17-B TS10 59 CH20-A CH20-B CH20-A CH20-B CH19-A CH19-B CH19-A CH19-B TS11 5A CH22-A CH22-B CH22-A CH22-B CH21-A CH21-B CH21-A CH21-B TS12 5B CH24-A CH24-B CH24-A CH24-B CH23-A CH23-B CH23-A CH23-B Note: In D4 format, TS1-TS12 contains signaling data for two frames. Bold type indicates data for second frame. Per-Channel Code (Idle) Generation Registers The method for generating idle codes has changed in the DS2155. The DS2155 contains a 64-byte Idle Code Array accessed by the Idle Array Address Register (IAAR) and the Per-Channel Idle Code Register (PCICR). The contents of the array contain the idle codes to be substituted into the appropriate transmit or receive channels. This substitution can be enabled and disabled on a per-channel basis by the Transmit Channel Idle Code Enable registers (TCICE1-4) and Receive Channel Idle Code Enable registers (RCICE1-4). The following table gives the DS2155 register that closely resembles the corresponding DS21x52 register. See section 18 of the DS2155 for additional information on per-channel idle code generation. DS21x52 Register: TIR1, TIR2, TIR3: Transmit Idle Registers 1, 2, 3 DS21x52 Register Address: 3C, 3D, 3E Hex DS21x52 Register: TIDR: Transmit Idle Definition Register DS21x52 Register Address: 3F Hex DS21x52 Register: TCC1, TCC2, TCC3: Transmit Channel Control Registers DS21x52 Register Address: 16, 17, 18 Hex DS21x52 Register: RMR1, RMR2, RMR3: Receive Mark Registers DS21x52 Register Address: 2D, 2E, 2F Hex DS21x52 Register: TC1 to TC24: Transmit Channel Registers DS21x52 Register Address: 50 to 57 Hex & 40 to 4F Hex DS21x52 Register: RC1 to RC24: Receive Channel Registers DS21x52 Register Address: 80 to 8F Hex & 58 to 5F Hex DS21x52 Register: RCC1, RCC2, RCC3: Receive Channel Control Registers DS21x52 Register Address: 1B, 1C, 1D Hex DS21x52 Register DS21x52 Register Abbreviation DS2155 Register Abbreviation DS2155 Address (Hex) Transmit Idle Register 1 TIR1 (3C Hex) TCICE1 80 Transmit Idle Register 2 TIR2 (3D Hex) TCICE2 81 Transmit Idle Register 3 TIR3 (3E Hex) TCICE3 82 Transmit Idle Definition Register TIDR (3F Hex) PCICR 7F Transmit Channel Control Register 1 TCC1 (16 Hex) PCDR1 29 Transmit Channel Control Register 2 TCC2 (17 Hex) PCDR2 2A Transmit Channel Control Register 3 TCC3 (18 Hex) PCDR3 2B Receive Mark Register 1 RMR1 (2D Hex) RCICE1 84 Receive Mark Register 2 RMR1 (2E Hex) RCICE2 85 Receive Mark Register 3 RMR1 (2F Hex) RCICE3 86 Transmit Channel Registers 1 to 24 TC1 to TC24 * * Receive Channel Registers 1 to 24 RC1 to RC24 * * Receive Channel Control Registers 1-3 RCC1 to RCC3 * * TC1 to TC24, RC1 to RC24, and RCC1 to RCC3 have been incorporated in the new functionality of the per-channel idle code generation. See section 18 of the DS2155 data sheet for more detail. Channel Blocking Registers DS21x52 Register: RCBR1, RCBR2, RCBR3: Receive Channel Block Registers DS21x52 Register Address: 6C, 6D, 6E Hex DS21x52 Register: TCBR1, TCBR2, TCBR3: Transmit Channel Block Registers DS21x52 Register Address: 32, 33, 34 Hex DS21x52 Register DS21x52 Register Abbreviation DS2155 Register Abbreviation DS2155 Address (Hex) Receive Channel Block Register 1 RCBR1 (6C Hex) RCBR1 88 Receive Channel Block Register 2 RCBR2 (6D Hex) RCBR2 89 Receive Channel Block Register 3 RCBR3 (6E Hex) RCBR3 8A Transmit Channel Block Register 1 TCBR1 (32 Hex) TCBR1 8C Transmit Channel Block Register 2 TCBR2 (33 Hex) TCBR2 8D Transmit Channel Block Register 3 TCBR3 (34 Hex) TCBR3 8E HDLC Registers While the DS21x52 has only one HDLC controller, the DS2155 has two enhanced HDLCs. Each controller is configurable for use with time slots, or Sa4 to Sa8 bits (E1 Mode) or the FDL (T1 Mode). The transmit and receive path buffers in the DS2155 have been doubled to 128-bytes. When used with time slots, the user can select any time slot or multiple time slots, contiguous or non-contiguous, as well as any specific bits within the time slot(s) to assign to the HDLC controllers. The HDLC controller performs the necessary overhead for generating and receiving Performance Report Messages (PRM) as described in ANSI T1.403 and the messages as described in AT&T TR54016. The HDLC controller automatically generates and detects flags, generates and checks the CRC check sum, generates and detects abort sequences, stuffs and de-stuffs zeros, and byte aligns to the data stream. The 128-byte buffers in the HDLC controller are large enough to allow a full PRM to be received or transmitted without host intervention. The user must take care to not map both transmit HDLC controllers to the same Sa bits, time slots or, in T1 mode, map both controllers to the FDL. HDLC #1 and HDLC #2 are identical in operation and therefore, when applicable, each DS21x52 register bit will be mapped to two addresses. DS21x52 Register: HCR: HDLC Control Register DS21x52 Register Address: 00 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RBR BOCC 37.3 6 RHR HxRC* 31.7 32.7 5 TFS HxTC* 90.3 A0.3 4 THR HxTC* 90.5 A0.5 3 TABT HxTC* See below 2 TEOM HxTC* 90.2 A0.2 1 TZSD HxTC* 90.1 A0.1 0 TCRCD HxTC* 90.0 A0.0 HxTC refers to H1TC and H2TC located at addresses 90 Hex and A0 Hex respectively. HxRC refers to H1RC and H2RC located at addresses 31 Hex and 32 Hex respectively. TABT, bit 3, has been incorporated into the Transmit HDLC Reset (THR) bit. DS21x52 Register: HSR: HDLC Status Register DS21x52 Register Address: 01 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RBOC SR8 24.0 6 RPE SR6 SR7 20.5 22.5 5 RPS SR6 SR7 20.4 22.4 4 RHALF SR6 SR7 20.3* 22.3* 3 RNE SR6 SR7 20.2 22.2 2 THALF SR6 SR7 20.1* 22.1* 1 TNF SR6 SR7 20.0 22.0 0 TMEND SR6 SR7 20.6 22.6 The status bits for HDLC #1 have been mapped to Status Register 6 (SR6) in the DS2155. The status bits for HDLC #2 have been mapped to Status Register 7 (SR7) in the DS2155. THALF, bit 2, has been renamed to TLWM. In the DS21x52, THALF is set when the transmit 64-byte FIFO empties beyond the halfway point. For the DS2155, the TLWM bit will be set when the transmit 128-byte FIFO empties beyond the low water mark as defined by the TFLWM0-TFLWM2 bits located in the FIFO control register (H1FC, H2FC). The low water mark is programmable to one of 8 different levels. RHALF, bit 4, has been renamed to RHWM. In the DS21x52, RHALF is set when the receive 64-byte FIFO fills beyond the halfway point. For the DS2155, the RHWM bit will be set when the receive 128-byte FIFO fills beyond the high water mark as defined by the RFHWM0-RFHWM2 bits located in the FIFO control register (H1FC, H2FC). The high water mark is programmable to one of 8 different levels. DS21x52 Register: HIMR: HDLC Interrupt Mask Register DS21x52 Register Address: 02 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RBOC IMR8 25.0 6 RPE IMR6 IMR7 21.5 23.5 5 RPS IMR6 IMR7 21.4 23.4 4 RHALF IMR6 IMR7 21.3* 23.3* 3 RNE IMR6 IMR7 21.2 23.2 2 THALF IMR6 IMR7 21.1* 23.1* 1 TNF IMR6 IMR7 21.0 23.0 0 TMEND IMR6 IMR7 21.6 23.6 The interrupt mask bits for HDLC #1 have been mapped to HDLC Interrupt Mask Register 6 (IMR6) in the DS2155. The interrupt mask bits for HDLC #2 have been mapped to HDLC Interrupt Mask Register 7 (IMR7) in the DS2155. THALF, bit 2, has been renamed to TLWM. When THALF is enabled in the DS21x52, the device will generate an interrupt when the transmit 64-byte FIFO empties beyond the halfway point. For the DS2155, the device will generate an interrupt, if TLWM is enabled, when the transmit 128-byte FIFO empties beyond the low water mark as defined by the TFLWM0-TFLWM2 bits located in the FIFO control register (H1FC, H2FC). The low water mark is programmable to one of 8 different levels. RHALF, bit 4, has been renamed to RLWM. When RHALF is enabled in the DS21x52, the device will generate an interrupt when the receive 64-byte FIFO fills beyond the halfway point. For the DS2155, the device will generate an interrupt, if RHWM is enabled, when the receive 128-byte FIFO fills beyond the high water mark as defined by the RFHWM0-RFHWM2 bits located in the FIFO control register (H1FC, H2FC). The high water mark is programmable to one of 8 different levels. DS21x52 Register: RHIR: Receive HDLC Information Register DS21x52 Register Address: 03 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RABT INFO5 INFO6 See below 6 RCRCE INFO5 INFO6 See below 5 ROVR INFO5 INFO6 See below 4 RVM INFO5 INFO6 See below 3 REMPTY INFO5 INFO6 2E.3 2F.3 2 POK INFO5 INFO6 See below 1 CBYTE HxRPBA* 9C.7* AC.7* 0 OBYTE INFO4* #1 2D.1* #2 2D.3* The HDLC information bits for HDLC #1 have been mapped to the Receive HDLC #1 Information Register, INFO5. The HDLC information bits for HDLC #2 have been mapped to the Receive HDLC #2 Information Register, INFO6. OBYTE, bit 0, is renamed as H1OBT for HDLC #1 and H2OBT for HDLC #2. Both H1OBT & H2OBT can be found in the HDLC Event Information Register (INFO4, address 2D Hex). There is no new functionality associated with this bit. HxRPBA refers to H1RPBA and H2RPBA, located at addresses 9C Hex and AC Hex respectively. CBYTE, bit 1, has been renamed as MS. Unlike the operation of the CBYTE bit in the DS21x52, the MS bit will be low when the byte available for reading the receive FIFO is the last byte of a message. MS will be high when the byte available for reading is the first byte of the continuation of a message. POK, bit 2, has been incorporated into the Receive Packet Status bits (PS0-PS2) located in INFO5 and INFO6. RVM, bit 4, has been incorporated into the Receive Packet Status bits (PS0-PS2) located in INFO5 and INFO6. ROVR, bit 5, has been incorporated into the Receive Packet Status bits (PS0-PS2) located in INFO5 and INFO6. RCRCE, bit 6, has been incorporated into the Receive Packet Status bits (PS0-PS2) located in INFO5 and INFO6. RABT, bit 7, has been incorporated into the Receive Packet Status bits (PS0-PS2) located in INFO5 and INFO6. DS21x52 Register: RBOC: Receive Bit Oriented Code Register DS21x52 Register Address: 04 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LBD SR2 18.7 6 BD INFO2 11.6 5 BOC5 See below See below 4 BOC4 See below See below 3 BOC3 See below See below 2 BOC2 See below See below 1 BOC1 See below See below 0 BOC0 See below See below BOC0-BOC5, bits 0-5, share the RFDL register in the DS2155. See section 22 of the DS2155 for additional information on the BOC controller. DS21x52 Register: RHFR: Receive HDLC FIFO DS21x52 Register Address: 05 Hex The Receive HDLC FIFO Register has been relocated to address 9E Hex for HDLC #1 and AE Hex for HDLC #2. The lower 7 bits of the Receive Packet Bytes Available registers (H1RPBA, H2RPBA) indicate the number of bytes that can be read from the receive FIFO. The value indicated by the lower seven bits in these registers informs the host as to how many bytes can be read from the receive FIFO without going past the end of a message. This value will refer to one of four possibilities, the first part of a packet, the continuation of a packet, the last part of a packet, or a complete packet. After reading the number of bytes indicated by this register the host then checks the HDLC Information register for detailed message status. See section 24.4.2 of the DS2155 data sheet for additional information. DS21x52 Register: THIR: Transmit HDLC Information Register DS21x52 Register Address: 06 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 - - - 6 - - - 5 - - - 4 - - - 3 - - - 2 TEMPTY INFO5 INFO6 2E.5 2F.5 1 TFULL INFO5 INFO6 2E.4 2F.4 0 TUDR INFO4* #1 2D.1* #2 2D.3* TUDR, bit 0, is renamed as H1UDR for HDLC #1 and H2UDR for HDLC #2. Both H1UDR & H2UDR can be found in the HDLC Event Information Register (INFO4, address 2D Hex). There is no new functionality associated with this bit. DS21x52 Register: TBOC: Transmit Bit Oriented Code Register DS21x52 Register Address: 07 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 SBOC BOCC 37.0 6 HBEN HxTC* 90.4* A0.4* 5 BOC5 See below See below 4 BOC4 See below See below 3 BOC3 See below See below 2 BOC2 See below See below 1 BOC1 See below See below 0 BOC0 See below See below BOC0-BOC5, bits 0-5, share the TFDL register in the DS2155. See section 22 of the DS2155 for additional information on the BOC controller. HxTC refers to H1TC and H2TC located at addresses 90 Hex and A0 Hex respectively. HBEN, bit 6, has been renamed as THMS. The THMS bit behaves in a different manner than the HBEN bit. See section 22 and 24 of the DS2155 for more information about the HDLCs operation. DS21x52 Register: THFR: Transmit HDLC FIFO DS21x52 Register Address: 08 Hex The Transmit HDLC FIFO Register has been relocated to address 9D Hex for HDLC #1 and AD Hex for HDLC #2. The Transmit FIFO Buffer Available registers (H1TFBA, H2TFBA) indicate the number of bytes that can be written into the transmit FIFOs. The count from this register informs the host as to how many bytes can be written into the transmit FIFO without overflowing the buffer DS21x52 Register: RDC1: Receive HDLC DS0 Control Register 1 DS21x52 Register Address: 90 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RDS0E HxRC 31.6* 32.6* 6 - - - 5 RDS0M See below See below 4 RD4 See below See below 3 RD3 See below See below 2 RD2 See below See below 1 RD1 See below See below 0 RD0 See below See below RD0 through RD4, bits 0 to 4, and RDS0M, bit 5, have been replaced by registers H1RCS1 to H1RCS4 for HDLC #1 and H2RCS1 to H2RCS4 for HDLC #2. Any channel or combination of channels, contiguous or not, can be assigned to an HDLC controller. When assigned to a channel(s) any combination of bits within the channel(s) can be avoided. See section 24.3 of the DS2155 for additional information on mapping the HDLC data to channels. HxRC refers to H1RC and H2RC located at addresses 31 Hex and 32 Hex respectively. RDS0E, bit 7, has been renamed to RHMS. The operation of this bit is inverted from that of the DS21x52. See section 24 of the DS2155 for additional information. DS21x52 Register: RDC2: Receive HDLC DS0 Control Register 2 DS21x52 Register Address: 91 Hex Receive HDLC DS0 Control Register 2 has been relocated to 96 Hex for HDLC #1 and A6 Hex for HDLC #2. DS21x52 Register: TDC1: Transmit HDLC DS0 Control Register 1 DS21x52 Register Address: 92 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 TDS0E HxTC 90.4* A0.4* 6 - - - 5 TDS0M See below See below 4 TD4 See below See below 3 TD3 See below See below 2 TD2 See below See below 1 TD1 See below See below 1 TD1 See below See below TD0 through TD4, bits 0 to 4, and TDS0M, bit 5, have been replaced by registers H1TCS1 to H1TCS4 for HDLC #1 and H2TCS1 to H2TCS4 for HDLC #2. Any channel or combination of channels, contiguous or not, can be assigned to an HDLC controller. When assigned to a channel(s) any combination of bits within the channel(s) can be avoided. See section 24.3 of the DS2155 for additional information on mapping the HDLC data to channels. HxTC refers to H1TC and H2TC located at addresses 90 Hex and A0 Hex respectively. TDS0E, bit 7, has been renamed to THMS. The operation of this bit is inverted from that of the DS21x52. See section 24 of the DS2155 for additional information. DS21x52 Register: TDC2: Transmit HDLC DS0 Control Register 2 DS21x52 Register Address: 93 Hex Transmit HDLC DS0 Control Register 2 has been relocated to 9B Hex for HDLC #1 and AB Hex for HDLC #2. DS21x52 Register: RFDL: Receive FDL Register DS21x52 Register Address: 28 Hex The Receive FDL Register has been relocated to address C0 Hex. The RFDL register will operate as the receive BOC message and information register when the receive BOC function is enabled by setting BOCC.4 to 1. The lower six bits of the RFDL register will contain the BOC message bits when used in this configuration. See section 22 of the DS2155 data sheet for more information. DS21x52 Register: RFDLM1, RFDLM2: Receive FDL Match Registers DS21x52 Register Address: 29 & 2A Hex Receive FDL Match Registers 1 and 2 have been relocated to address C2 Hex and C3 Hex, respectively. DS21x52 Register: TFDL: Transmit FDL Register DS21x52 Register Address: 7E Hex The Transmit FDL Register has been relocated to address C1 Hex. The TFDL register will operate as the transmit BOC message register when the transmit BOC function is enabled by setting BOCC.0 to 1. The lower six bits of the TFDL register will contain the BOC message to be transmitted. See section 22 of the DS2155 data sheet for additional information. Line Interface, Programmable In-Band Loop Code, and Transmit Transparency Registers DS21x52 Register: LICR: Line Interface Control Register DS21x52 Register Address: 7C Hex DS21x52 Register: IBCC: In-Band Code Control Register DS21x52 Register Address: 12 Hex DS21x52 Register: TCD: Transmit Code Definition Register DS21x52 Register Address: 13 Hex DS21x52 Register: RUPCD: Receive Up Code Definition Register DS21x52 Register Address: 14 Hex DS21x52 Register: RDNCD: Receive Down Code Definition Register DS21x52 Register Address: 15 Hex DS21x52 Register: TTR1, TTR2, TTR3: Transmit Transparency Registers DS21x52 Register Address: 39, 3A, 3B Hex DS21x52 Register DS21x52 Register Abbreviation DS2155 Register Abbreviation DS2155 Address (Hex) Line Interface Control Register LICR (7C Hex) LIC1 78 In-Band Code Control Register IBCC (12 Hex) IBCC B6 Transmit Code Definition Register TCD (13 Hex) TCD1* B7* Receive Up Code Definition Register RUPCD (14 Hex) RUPCD1* B9* Receive Down Code Definition Register RDNCD (15 Hex) RDNCD1* BB* Transmit Transparency Register 1 TTR1 SSIE1 08 Transmit Transparency Register 2 TTR2 SSIE2 09 Transmit Transparency Register 3 TTR3 SSIE3 0A The DS2155's programmable in-band loop code generation and detection includes support for 16-bit codes. In adding this feature a second register has been added for transmit code definition and receive up/down code definition. For generation or detection of 8 bit patterns, both of the appropriate definition registers must be filled with the same value. See section 26 of the DS2155 data sheet for additional information. Interleaved PCM Bus Operation Register The interleave bus operation has been converted to full software control in the DS2155 and the external pins associated with this option have been reassigned to the extended system information bus function. See section 29 for more detail on the interleaved PCM bus operation. DS21x54 Register: IBO: Interleaved Bus Operation Register DS21x54 Register Address: 94 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 - - - 6 - - - 5 - - - 4 - - - 3 IBOEN IBOC C5.3 2 INTSEL IBOC C5.3* 1 MSEL0 See below See below 0 MSEL1 See below See below MSEL0 and MSEL1 are not included in the DS2155. INTSEL, bit 2, has been renamed IBOSEL. There is no new functionality associated with this control bit. 3. Software Considerations: DS2155 vs. DS21x54 (E1) This section will present the registers for the DS21354 and DS21554. The registers are presented in the order that they appear in the DS21354 and DS21554 data sheet. ID Register DS21x54 Register: IDR: Device Identification Register DS21x54 Register Address: 0F Hex The Device Identification Register (IDR) for the DS2155 is located at the same address as the IDR for the DS21x54. The upper four bits display the DS2155 ID (1011) and the lower four bits display the die revision. Receive Control Registers DS21x54 Register: RCR1: Receive Control Register 1 DS21x54 Register Address: 10 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RSMF IOCR1 01.6* 6 RSM IOCR1 01.5* 5 RSIO IOCR1 01.4 4 - - - 3 - - - 2 FRC E1RCR1 33.2 1 SYNCE E1RCR1 33.1 0 RESYNC E1RCR1 33.0 RSM, bit 6, has been renamed as RSMS1. There is no new functionality associated with the bit. RSDW, bit 7, has been renamed as RSMS2. There is no new functionality associated with the bit. DS21x54 Register: RCR2: Receive Control Register 2 DS21x54 Register Address: 11 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 Sa8S E1RCR2 34.7 6 Sa7S E1RCR2 34.6 5 Sa6S E1RCR2 34.5 4 Sa5S E1RCR2 34.4 3 Sa4S E1RCR2 34.3 2 RBCS IOCR2 02.0* 1 RESE ESCR 4F.0 0 - - - RBCS, bit 2, has been renamed as RSCLKM. There is no new functionality associated with the bit. Transmit Control Registers DS21x54 Register: TCR1: Transmit Control Register 1 DS21x54 Register Address: 12 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 ODF IOCR1 01.0 6 TFPT E1TCR1 35.7 5 T16S E1TCR1 35.6 4 TUA1 E1TCR1 35.5 3 TsiS E1TCR1 35.4 2 TSA1 E1TCR1 35.3 1 TSM IOCR1 01.2 0 TSIO IOCR1 01.1 DS21x54 Register: TCR2: Transmit Control Register 2 DS21x54 Register Address: 13 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 Sa8S E1TCR2 36.7 6 Sa7S E1TCR2 36.6 5 Sa6S E1TCR2 36.5 4 Sa5S E1TCR2 36.4 3 Sa4S E1TCR2 36.3 2 ODM CCR1 70.4 1 AEBE E1TCR2 36.2 0 PF CCR1 70.0* PF, bit 0, has been renamed as RLOSF. There is no new functionality associated with the bit. Common Control Registers DS21x54 Register: CCR1: Common Control Register 1 DS21x54 Register Address: 14 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 FLB LBCR 4A.0 6 THDB3 E1TCR1 35.2 5 TG802 E1TCR1 35.1 4 TCRC4 E1TCR1 35.0 3 RSM E1RCR1 33.6* 2 RHDB3 E1RCR1 33.5 1 RG802 E1RCR1 33.4 0 RCRC4 E1RCR1 33.3 RSM, bit 3, has been renamed as RSIGM. There is no new functionality associated with the bit. DS21x54 Register: CCR2: Common Control Register 2 DS21x54 Register Address: 1A Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 ECUS ERCNT 41.5 6 VCRFS ERCNT 41.3 5 AAIS E1TCR2 36.1 4 ARA E1TCR2 36.0 3 RSERC E1RCR1 33.7 2 LOTCMC CCR1 See below 1 RFF SIGCR 40.3 0 RFE SIGCR 40.4 LOTCMC, bit 2, has been combined with other functions to simplify the selection of the transmit clock source. The two bits, Transmit Clock Source Select 0 (TCSS0) and Transmit Clock Source Select 1 (TCSS1), are located in the DS2155's Common Control Register 1 (CCR1, address 70 Hex) in bit positions 1 and 2 respectively. DS21x54 Register: CCR3: Common Control Register 3 DS21x54 Register Address: 1B Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 TESE ESCR 4F.4 6 TCBFS See Below See Below 5 TIRFS See Below See Below 4 - - - 3 RSRE PCPR 28.6* 2 THSE PCPR 28.3* 1 TBCS IOCR2 02.1* 0 RCLA E1RCR2 34.0 TBCS, bit 1, has been renamed as TSCLKM. There is no new functionality associated with this bit. THSE, bit 2, has been renamed as THSCS. See sections 7 and 17 of the DS2155 data sheet for information on per-channel register operation. RSRE, bit 3, has been renamed as RSRCS. See sections 7 and 17 of the DS2155 data sheet for additional information on receive signaling re-insertion. Control bit 5, TIRFS, has been incorporated in the new functionality for idle code generation. See section 18 of the DS2155 data sheet for more detail. Control bit 6, TCBFS, has been incorporated into the per-channel register operation. See sections 7 and 17 of the DS2155 data sheet for additional information. DS21x54 Register: CCR4: Common Control Register 4 DS21x54 Register Address: A8 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RLB LBCR 4A.2 6 LLB LBCR 4A.3 5 LIAIS LIC2 79.4* 4 TCM4 TDS0SEL 74.4 3 TCM3 TDS0SEL 74.3 2 TCM2 TDS0SEL 74.2 1 TCM1 TDS0SEL 74.1 0 TCM0 TDS0SEL 74.0 LIAIS, bit 1, has been renamed as TUA1. There is no new functionality associated with this bit. DS21x54 Register: CCR5: Common Control Register 5 DS21x54 Register Address: AA Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LIRST LIC2 79.6 6 RESA ESCR 4F.3* 5 TESA ESCR 4F.7* 4 RCM4 RDS0SEL 76.4 3 RCM3 RDS0SEL 76.3 2 RCM2 RDS0SEL 76.2 1 RCM1 RDS0SEL 76.1 0 RCM0 RDS0SEL 76.0 TESA, bit 5, has been renamed as TESALGN. There is no new functionality associated with the bit. RESA, bit 6, has been renamed as RESALGN. There is no new functionality associated with the bit. DS21x54 Register: CCR6: Common Control Register 6 DS21x54 Register Address: 1D Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 LIUODO LIC2 79.0* 6 CDIG LIC3 7A.0* 5 LIUSI LIC3 7A.2* 4 - - - 3 - - - 2 TCLKSRC CCR1 See below 1 RESR ESCR 4F.2 0 TESR ESCR 4F.6 TCLKSRC, bit 2, has been combined with other functions to simplify the selection of the source for the transmit clock. Two bits, Transmit Clock Source Select bit 0 (TCSS0) and bit 1 (TCSS1) are located in the DS2155's Common Control Register 1 (CCR1, address 70 Hex) in bit positions 1 and 2 respectively. LIUSI, bit 5, has been renamed as RSCLKE. There is no new functionality associated with the bit. However, there is now a TSCLKE control bit available in the DS2155, which controls G.703 support for the transmitter. CDIG, bit 6, has been renamed as TAOZ. There is no new functionality associated with the bit. LIUODO, bit 7, has been renamed as CLDS. In the DS21x54, this bit determined whether the TTIP and TRING outputs would be open drain or not. In the DS2155, setting this bit to a one will redefine the operation of the transmit line driver. When this bit is set to a one and LIC1.5 = LIC1.6 = LIC1.7 = 0, then the device will generate a square wave at the TTIP and TRING outputs instead of a normal waveform. When this bit is set to a one and LIC1.5 = LIC1.6 = 0 and LIC1.7 = 1, then the device will force TTIP and TRING outputs to become open drain drivers instead of their normal push-pull operation. This bit should be set to zero for normal operation of the DS2155. Status and Information Registers DS21x54 Register: RIR: Receive Information Register DS21x54 Register Address: 08 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 TESF SR5 1E.5 6 TESE SR5 1E.4* 5 JALT SR1 16.4 4 RESF SR5 1E.2 3 RESE SR5 1E.1* 2 CRCRC INFO3 12.2 1 FASRC INFO3 12.1 0 CASRC INFO3 12.0 RESE, bit 3, has been renamed as RESEM. There is no new functionality associated with this bit. TESE, bit 6, has been renamed as TESEM. There is no new functionality associated with this bit. DS21x54 Register: SSR: Synchronizer Status Register DS21x54 Register Address: 1E Hex The Synchronizer Status Register has been relocated to address 30 Hex in the DS2155. DS21x54 Register: SR1: Status Register 1 DS21x54 Register Address: 06 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RSA1 SR4 1C.6 6 RDMA SR3 1A.1 5 RSA0 SR4 1C.5 4 RSLIP SR5 1E.0 3 RUA1 SR2 18.2 2 RRA SR3 1A.0 1 RCL SR1 16.3* 0 RLOS SR2 18.0 RCL, bit 1, has been renamed as LRCL. No additional functionality is associated with this bit. DS21x54 Register: SR2: Status Register 2 DS21x54 Register Address: 07 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RMF SR4 1C.2 6 RAF SR4 1C.0 5 TMF SR4 1C.4 4 SEC SR1 16.6* 3 TAF SR4 1C.3 2 LOTC SR3 1A.4 1 RCMF SR4 1C.1 0 TSLIP SR5 1E.3 SEC, bit 5, has been renamed as TIMER. In the DS21x54, this bit was set on increments of one second (referenced to RCLK). In the DS2155, this bit follows the error counter update interval as determined by the ECUS bit in the Error Counter Configuration Register (ERCNT). In T1 mode, this bit can be configured to set on increments of 1 second or 42ms (referenced to RCLK). DS21x54 Register: IMR1: Interrupt Mask Register 1 DS21x54 Register Address: 16 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RSA1 IMR4 1D.6 6 RDMA IMR3 1B.1 5 RSA0 IMR4 1D.5 4 RSLIP IMR5 1F.0 3 RUA1 IMR2 19.2 2 RRA IMR3 1B.0 1 RCL IMR1 17.3* 0 RLOS IMR2 19.0 RCL, bit 1, has been renamed as LRCL. No additional functionality is associated with this bit. DS21x54 Register: IMR2: Interrupt Mask Register 2 DS21x54 Register Address: 17 Hex Bit # Name 55 Abbrv. 55 Addr.Bit 7 RMF IMR4 1D.2 6 RAF IMR4 1D.0 5 TMF IMR4 1D.4 4 SEC IMR1 17.6* 3 TAF IMR4 1D.3 2 LOTC IMR3 1B.4 1 RCMF IMR4 1D.1 0 TSLIP IMR5 1F.3 SEC, bit 5, has been renamed as TIMER. In the DS21x54, this bit enabled the interrupt on increments of one second (referenced to RCLK). In the DS2155, this bit follows the error counter update interval as determined by the ECUS bit in the Error Counter Configuration Register (ERCNT). In T1 mode, this bit can be configured to interrupt on increments of 1 second or 42ms (referenced to RCLK). Error Count Registers The error count registers have been kept intact, but have been relocated. In addition, all of the count registers are now 16-bit registers because the registers that were shared in the DS21x54 are no longer shared in the DS2155. See section 15 in the DS2155 data sheet for additional information on the error count registers. DS21x54 Registers: VCR1, VCR2: Bipolar Violation Count Register 1 & 2 DS21x54 Register Address: 00, 01 Hex DS21x54 Registers: CRCCR1, CRCCR2: CRC4 Count Register 1 & 2 DS21x54 Register Address: 02 Hex (Same as FASCR1), 03 Hex DS21x54 Register: FASCR1, FASCR2: FAS Error Count Register 1 & 2 DS21x54 Register Address: 02 Hex (Same as CRCCR1), 04 Hex (Same as EBCR1) DS21x54 Register: EBCR1, EBCR2: E-Bit Count Register 1 & 2 DS21x54 Register Address: 04 Hex (Same as FASCR2), 05 Hex DS21x54 Register DS21x54 Register Abbreviation DS2155 Register Abbreviation DS2155 Address (Hex) Bipolar Violation Count Register 1 VCR1 (00 Hex) LCVCR1 42 Bipolar Violation Count Register 2 VCR2 (01 Hex) LCVCR2 43 CRC4 Count Register 1 CRCCR1 (02 Hex)* PCVCR1 44 CRC4 Count Register 2 CRCCR2 (03 Hex) PCVCR2 45 FAS Error Count Register 1 FASCR1 (02 Hex)* FOSCR1 46 FAS Error Count Register 2 FASCR2 (04 Hex)* FOSCR2 47 E-Bit Error Count Register 1 EBCR1 (04 Hex)* EBCR2 48 E-Bit Error Count Register 2 EBCR2 (05 Hex) EBCR2 49 In the DS21x54, CRCCR1 and FASCR1 shared the count register located at address 02 Hex. The two error counters no longer share a register in the DS2155. Additionally, FASCR2 and EBCR1 shared the count register located at address 04 Hex. These two error counters no longer share a register in the DS2155. DS0 Monitoring Function Registers Both the Transmit DS0 Monitor Register and Receive DS0 Monitor Register has been relocated to a new address. DS21x54 Register: TDS0M: Transmit DS0 Monitor Register DS21x54 Register Address: A9 Hex DS21x54 Register: RDS0M: Receive DS0 Monitor Register DS21x54 Register Address: AB Hex DS21x54 Register DS21x54 Register Abbreviation DS2155 Register Abbreviation DS2155 Address (Hex) Transmit DS0 Monitor Register TDS0M (A9 Hex) TDS0M 75 Receive DS0 Monitor Register RDS0M (AB Hex) RDS0M 77 Signaling Registers The Transmit Signaling Registers and Receive Signaling Registers have been relocated to 50-5F Hex and 60-6F Hex, respectively. Additionally, the signaling information contained in the signaling registers has been rearranged. See section 17 of the DS2155 data sheet for additional information on signaling operation. DS21x54 Register: RS1 to RS16: Receive Signaling Registers DS21x54 Register Address: 30 to 3F Hex The Receive signaling registers have been relocated to 60-6F Hex The following table shows the new the arrangement for the Receive Signaling Registers. Transmit Signaling Registers (T1 Mode, ESF Format) Register Name DS2155 Address   (MSB)             (LSB) RS1 60 CH2-A CH2-B CH2-C CH2-D CH1-A CH1-B CH1-C CH1-D RS2 61 CH4-A CH4-B CH4-C CH4-D CH3-A CH3-B CH3-C CH3-D RS3 62 CH6-A CH6-B CH6-C CH6-D CH5-A CH5-B CH5-C CH5-D RS4 63 CH8-A CH8-B CH8-C CH8-D CH7-A CH7-B CH7-C CH7-D RS5 64 CH10-A CH10-B CH10-C CH10-D CH9-A CH9-B CH9-C CH9-D RS6 65 CH12-A CH12-B CH12-C CH12-D CH11-A CH11-B CH11-C CH11-D RS7 66 CH14-A CH14-B CH14-C CH14-D CH13-A CH13-B CH13-C CH13-D RS8 67 CH16-A CH16-B CH16-C CH16-D CH15-A CH15-B CH15-C CH15-D RS9 68 CH18-A CH18-B CH18-C CH18-D CH17-A CH17-B CH17-C CH17-D RS10 69 CH20-A CH20-B CH20-C CH20-D CH19-A CH19-B CH19-C CH19-D RS11 6A CH22-A CH22-B CH22-C CH22-D CH21-A CH21-B CH21-C CH21-D RS12 6B CH24-A CH24-B CH24-C CH24-D CH23-A CH23-B CH23-C CH23-D RS13 6C CH26-A CH26-B CH26-C CH26-D CH25-A CH25-B CH25-C CH25-D RS14 6D CH28-A CH28-B CH28-C CH28-D CH27-A CH27-B CH27-C CH27-D RS15 6E CH30-A CH30-B CH30-C CH30-D CH29-A CH29-B CH29-C CH29-D RS16 6F CH32-A CH32-B CH32-C CH32-D CH31-A CH31-B CH31-C CH31-D DS21x54 Register: TS1 to TS16: Transmit Signaling Registers DS21x54 Register Address: 40 to 4F Hex Transmit Signaling Registers 1 through 16 can be found at addresses 50 Hex through 5F Hex. In E1 mode, TS16 carries the signaling information. This information can be in either CCS (Common Channel Signaling) or CAS (Channel Associated Signaling) format. The 32 time slots are referenced by two different channel number schemes in E1. In "Channel" numbering, TS0 through TS31 are labeled channels 1 through 32. In "Phone Channel" numbering TS1 through TS15 are labeled channel 1 through channel 15 and TS17 through TS31 are labeled channel 15 through channel 30. See table 17-1 in the DS2155 for more information. The following tables show the new the arrangement for the Transmit Signaling Registers for CAS and CCS formats. Transmit Signaling Registers (E1 Mode, CAS Format) Register Name DS2155 Address   (MSB)             (LSB) TS1 50 0 0 0 0 X Y X X TS2 51 CH2-A CH2-B CH2-C CH2-D CH1-A CH1-B CH1-C CH1-D TS3 52 CH4-A CH4-B CH4-C CH4-D CH3-A CH3-B CH3-C CH3-D TS4 53 CH6-A CH6-B CH6-C CH6-D CH5-A CH5-B CH5-C CH5-D TS5 54 CH8-A CH8-B CH8-C CH8-D CH7-A CH7-B CH7-C CH7-D TS6 55 CH10-A CH10-B CH10-C CH10-D CH9-A CH9-B CH9-C CH9-D TS7 56 CH12-A CH12-B CH12-C CH12-D CH11-A CH11-B CH11-C CH11-D TS8 57 CH14-A CH14-B CH14-C CH14-D CH13-A CH13-B CH13-C CH13-D TS9 58 CH16-A CH16-B CH16-C CH16-D CH15-A CH15-B CH15-C CH15-D TS10 59 CH18-A CH18-B CH18-C CH18-D CH17-A CH17-B CH17-C CH17-D TS11 5A CH20-A CH20-B CH20-C CH20-D CH19-A CH19-B CH19-C CH19-D TS12 5B CH22-A CH22-B CH22-C CH22-D CH21-A CH21-B CH21-C CH21-D TS13 5C CH24-A CH24-B CH24-C CH24-D CH23-A CH23-B CH23-C CH23-D TS14 5D CH26-A CH26-B CH26-C CH26-D CH25-A CH25-B CH25-C CH25-D TS15 5E CH28-A CH28-B CH28-C CH28-D CH27-A CH27-B CH27-C CH27-D TS16 5F CH30-A CH30-B CH30-C CH30-D CH29-A CH29-B CH29-C CH29-D Transmit Signaling Registers (E1 Mode, CCS Format) Register Name DS2155 Address   (MSB)             (LSB) TS1 50 1 2 3